Toshiba 16SKVP2 Series Kullanıcı El Kitabı - Sayfa 3

Klima Toshiba 16SKVP2 Series için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Toshiba 16SKVP2 Series 6 sayfaları. Split type

Sayfayı Yazdır

Toshiba 16SKVP2 Series Kullanıcı El Kitabı

TEMPORARY OPERATION

In case of the misplaced or discharged remote control

•

Pressing the RESET button, the unit can start or stop

without using the remote control.

•

Operation mode is set on AUTOMATIC operation, preset

temperature is 25°C and fan operation is automatic

speed.

TIMER OPERATION

Setting the ON Timer

Press

for enter ON timer setting

Press

for select desired ON

timer.

Press

for set timer.

Press

for cancel timer.

Daily timer allows the user to set both the ON & OFF timers and will be

activated on a daily basis.

Setting Daily Timer

Press

for enter ON timer setting

Press

for select desired

ON timer.

Press

for enter OFF timer setting

•

During the daily timer is activating, both arrows (

Note:

•

Keep the remote control in accessible transmission to the indoor unit;

otherwise, the time lag of up to 15 minutes will occur.

•

The setting will be saved for the next same operation.

PRESET OPERATION

Set your preferred operation for future use. The setting will be memorized by the

unit for future operation (except airﬂ ow direction).

1. Select your preferred operation.

2. Press and hold

for 3 seconds to memorize the setting.

The P mark displays.

3. Press

: Operate the preset operation.

AUTO RESTART OPERATION

To automatically restart the conditioner after the power failure (Power of the unit must

be on.)

Setting

1. Press and hold the RESET button on the indoor unit for 3 seconds to set the

operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)

2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the

operation. (3 beep sound but OPERATION lamp does not blink)

•

In case of ON timer or OFF timer are set, AUTO RESTART OPERATION does

not activate.

POWER-SELECTION OPERATION

This function is used when its circuit breaker is shared with other electrical

appliances. It limits the maximum current/ power consumption to 100%, 75% or

50%. The lower the percentage, the higher the saving and also the longer the

compressor lifetime.

Press

: Select:

(for 100%),

•

When the level is selected, PWR-SEL level ﬂ ashes on LCD display for 3

seconds. In case of 75% and 50% level, number "75" or "50" also ﬂ ashes

for 2 seconds.

•

Due to the reason that POWER SELECT FUNCTION limits the maximum

current, inadequate capacity may occur.

COMFORT SLEEP OPERATION

To save energy while sleeping, automatically control air ﬂ ow and automatically

turn OFF.

Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note: The cooling operation, the set temperature will increase automatically

1 degree/hour for 2 hours (maximum 2 degrees increase). For heating

operation, the set temperature will decrease.

8°C OPERATION

1. Press

button to change to 8°C set temperature heating operation.

2. Press

to adjust setting temperature from 5°C to 13°C.

Note: 8°C will operate in Heating mode only. If Air conditioner performs in cooling

operation (including automatic cooling) or dry operation it will change to

heating operating.

Setting the OFF Timer

Press

for enter OFF timer setting

Press

for select desired OFF

timer.

Press

for set timer.

Press

for cancel timer.

Press

for select desired OFF

timer.

Press

again during the

( or ) blink.

, ) are indicated.

(for 75%),

(for 50%)

MAINTENANCE

Firstly, turn off the circuit breaker.

Filter Reset (Some models only)

FILTER lamp lights on; the ﬁ lter must be cleaned.

To turn off the lamp, push the RESET button on the indoor unit or the FILTER button on

the remote control.

Indoor Unit and Remote Control

•

Clean the indoor unit and the remote control with a wet cloth when needed.

•

No benzine, thinner, polishing powder or chemically-treated duster.

Cleaning the air ionizer (Once every six months)

1. Turn off air conditioner using remote control and power supply.

2. Fully open the vertical air ﬂ ow louvers by hand.

3. Use a toothbrush to rub the ends of metal pin three or four times.

Note: Do not use cotton swabs or other objects with ﬂ uff.

Cleaning the plasma air puriﬁ er unit (About 1000 hours performed)

1. Turn off air conditioner using remote control and power supply.

2. Take out the air inlet grille (See detail in installation manual).

3. Take out the plasma air puriﬁ er by grasp the handle, and the pull it out.

4. Soak in hot water at 40°C to 50°C for about 10 to 15 minutes and rub up, down, left,

right and rub surface gently with a sponge.

5. Allow to dry thoroughly in the shade.

6. Attach the plasma air puriﬁ er by grasp the handle

and insert into the right and left guide rails.

7. Press both ends of the plasma air puriﬁ er until the

protrusions on both sides of the plasma air puriﬁ er

are completely inserted.

8. Attach the air ﬁ lter, and then close the air inlet grille.

SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)

To protect bad smell caused by the humidity in the indoor unit.

1. If the

button is pressed once during "Cool" or "Dry" mode, the fan

will continue to run for other 30 minutes, then it will turn off automatically.

This will reduce the moisture in the indoor unit.

2. To stop the unit immediately, press the

seconds.

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated for 3

minutes when suddenly restarted or switched to ON.

2. Preheating operation: Warm up the unit for 5 minutes before the heating operation

starts.

3. Warm air control: When the room temperature reaches the set temperature, the fan

speed is automatically reduced and the outdoor unit will stop.

4. Automatic defrosting: Fans will stop during defrost operation.

5. Heating capacity: Heat is absorbed from outdoors and released into the room. When

the outdoor temperature is too low, use another recommended heating apparatus in

combination with the air conditioner.

6. Consideration for accumulated snow: Select the position for outdoor unit where it will

not be subjected to snow drifts, accumulation of leaves or other seasonal debris.

7. Some minor cracking sound may occur when unit operating. This is normal because

the cracking sound may be caused by expansion/contraction of plastic.

Note: Item 2 to 6 for Heating model

Air conditioner operating conditions

Temp.

Outdoor Temperature

Operation

Heating

–15°C ~ 24°C

Cooling

–10°C ~ 46°C

Dry

–10°C ~ 46°C

TROUBLESHOOTING (CHECK POINT)

The unit does not operate.

•

The power main switch is

•

The ﬁ lters are blocked with dust.

turned off.

•

The temperature has been set improperly.

•

The circuit breaker is activated

•

The windows or doors are opened.

to cut off the power supply.

•

The air inlet or outlet of the outdoor unit is blocked.

•

Stoppage of electric current

•

The fan speed is too low.

•

ON timer is set.

•

The operation mode is FAN or DRY.

•

POWER SELECT FUNCTION is set at 75% or 50%.

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air

conditioner are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold

button on the Remote Control by the tip of the pencil.

"00" will be shown on the display.

4. Press

during pushing

will disappear and the air conditioner will turn OFF. The Remote Control B

is memorized.

Note:

1. Repeat above step to reset

Remote Control to be A.

2. Remote Control A has not "A"

display.

3. Default setting of Remote Control

from factory is A.

more 2 times within 30

Room Temperature

Less than 28°C

21°C ~ 32°C

17°C ~ 32°C

Cooling or Heating is abnormally low.

. "B" will show on the display and "00"