Epson PowerLite 735c Ürün Bilgileri - Sayfa 10

Yazılım Epson PowerLite 735c için çevrimiçi göz atın veya pdf Ürün Bilgileri indirin. Epson PowerLite 735c 14 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson PowerLite 735c için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Kullanıcı Kılavuzu (29 sayfalar), Teknik Özellikler (2 sayfalar), Kullanım Kılavuzu (47 sayfalar), Parça Listesi (1 sayfalar), Ürün Destek Bülteni (30 sayfalar), Kurulum Kılavuzu (19 sayfalar), Hızlı Kurulum Kılavuzu (2 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar)

Sayfayı Yazdır

EPSON PowerLite 735c Projector

6. To customize transitions between slides, click the cell or

cells you want to set up. (To select more than one cell, hold

down the

key while you click.) Then right-click the

Ctrl

selected cell(s) in the scenario window and click

. Choose from any of the following options:

Properties

❏ Select

On mouse click

manually using the remote control.

❏ If you want your slides to advance automatically, click

Automatically after

and 1800 seconds (30 minutes). Even if you select this

setting, you can still change slides manually using the

remote control.

❏ To add a transition effect such as a dissolve or fade,

select one of the

Animation Effects

, if applicable. Then click

Direction

Properties window.

7. Click

. Then continue with the steps in the next

Save

section to transfer your scenario to a memory card.

Transferring the Scenario to a Memory Card

Before you start, make sure you're set up to access the card in

your computer's PCMCIA slot or card reader. Follow the

procedure below to make sure the scenario plays properly.

Note: You have to save the scenario on your computer's hard drive

before transferring it. Don't use Windows to copy the scenario to

your memory card, or it may not play properly.

1. From the Scenario Option menu, choose

You see a drive selection window.

2. Choose the drive where your card is located, then click

3. Click

again to confirm. Your scenario is transferred to

the card. You see this message:

4. Do one of the following:

❏ If you don't want the scenario to run automatically

whenever the projector is turned on (with the memory

card in the projector), click

card from your computer and insert it in the projector.

❏ To run the scenario automatically when the projector is

turned on, click

select the scenario from the list on the left and use the

arrow button to move it to the

on the right. Click

remove the card from your computer and insert it in

the projector.

EPSON PowerLite 735c Projector

Cell

if you want to change slides

, then set a length of time between 1

and choose a

to close the cell

Send Scenario

. Then remove the

Cancel

. On the Edit Autorun window,

Autorun Scenario List

when you're done, and then

Note: If more than one scenario is set to run automatically, they

will play in the order listed in the Autorun Scenario List.

Projector Status Lights

The lights on top of the projector indicate the projector's

status and let you know when a problem occurs.

Power

Lamp/

light

Temperature

light

Green

Off

Flashing

Off

green

Orange

Off

Flashing

Off

orange

—

Flashing

orange

—

Flashing red

2/03

Power light

Lamp/temperature

light

Description and action

The projector is operating normally.

The projector is warming up. Wait

for the image to appear.

The projector is in standby mode.

You can unplug it or press the

Power

button to turn it on.

The projector is cooling down. Wait

for the light to stop flashing before

unplugging it.

The projector is too hot. Make sure

the room temperature is not above

95 °F and there is plenty of space

around and under the projector for

ventilation. Also, the air filter may be

clogged. Clean or replace it, as

described on page 11.

Power is cut off because of an

internal error in the projector.

Unplug the projector and contact

EPSON.