Epson PowerLite 737c Ürün Bilgileri - Sayfa 13

Yazılım Epson PowerLite 737c için çevrimiçi göz atın veya pdf Ürün Bilgileri indirin. Epson PowerLite 737c 24 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson PowerLite 737c için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Hızlı Kurulum Kılavuzu (2 sayfalar), Kullanım Kılavuzu (47 sayfalar), Parça Listesi (1 sayfalar), Ürün Destek Bülteni (30 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar), Hızlı Kurulum (2 sayfalar)

Sayfayı Yazdır
Epson PowerLite 737c Ürün Bilgileri
3. Click the
button. Then click the
Configure
on the screen that appears. You see a screen like this:
4. Ad hoc mode: Highlight
and set the Value to
802.11 Ad Hoc
Access point mode: Highlight
Value to
Infrastructure
5. Ad hoc mode: Highlight
the name you gave the projector's ESSID (for example,
).
CONF ROOM
Access point mode: Highlight
match the name assigned to the access point.
Note:
The SSID is case-sensitive.
6. Highlight
and make sure it is disabled.
Encryption
7. Click the
tab and make sure the network card or
General
wireless network device is enabled.
8. Ad hoc mode: Click
OK
properties dialog box. Then go to "Projecting Wirelessly" on
page 15.
Access point mode: On the General tab, select
, then click the
Protocol
screen:
Advanced
in the Property list
Network Type
.
and set the
Network Type
.
and set the Value to match
SSID
and set the Value to
SSID
to close the network card's
Internet
button. You see this
Properties
tab
9. If your access point uses DHCP, select
automatically
and enter the required information.
address
❏
IP address
to the computer. It must be formatted like other
addresses on the network; usually the first three sections
(XXX.XXX.XXX) match the access point's IP address,
and the last section is unique.
❏
Subnet mask
this too must match how your network is set up.
❏
Default gateway
assigned to the access point when it was set up.
10.When done, click
11.Click the
Wireless Networks
Note:
If you don't see this tab, you may need to enable your wireless
card or network device by clicking
device settings; then follow any instructions on the screen to
enable the device.
2/05
Epson PowerLite 737c Projector
Obtain IP address
. Otherwise, select
Use the following IP
: Type in the IP address you want to assign
: For example, 255.255.255.000, but
: Enter the IP address that was
.
OK
tab. You see this screen:
Configure
Epson PowerLite 737c Projector
to access the
13
-