Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C Kullanıcı Kılavuzu - Sayfa 18
Stereo sistemi Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C 31 sayfaları. 3 cd changer with dolby® pro logic processor, five loudspeakers, 320 watts total power
Ayrıca Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C için: Teknik Özellikler (2 sayfalar), Manuel (31 sayfalar)
Sayfayı Yazdır
CD
Playing a CD
1 Press PLAYÉ Å to start playback.
™ The disc tray, track number and
elapsed playing time of the current
track appear on the display.
• To interrupt playback, press
PAUSEÉ Å .
™ The playing time flashes.
• To resume playback, press PLAYÉ Å
again.
2 To stop playback, press Ç.
Notes:
– All the available discs will play once,
then stop.
– When the CD has stopped playing, the
system will switch to standby mode
after 30 minutes if no button is pressed.
18
pg 01-31/P88/22-Eng
18
Disc Change
You can change the outer two discs while
the third inner disc is stopped or is playing.
1 Press DISC CHANGE.
™ The CD carousel tray slides out.
2 Replace the discs in the left and right
disc trays.
• If you wish to change the inner disc
during playback, press DISC CHANGE
again.
™ "DISC CHANGE" will be displayed.
™ The CD will stop playing.
™ The CD carousel tray will close to
retrieve the inner CD and then open
again with the inner CD accessible.
3 Press OPEN•CLOSE to close the CD
carousel tray.
Selecting a desired track
Selecting a desired track when
playback is stopped
1 Press í or ë (or Digit 0-9 on the
remote control) until the desired track
appears on the display.
2 Press PLAYÉ Å to start playback.
™ The selected track number and
elapsed playing time appear on the
display.
Selecting a desired track during
playback
• Press í or ë (or Digit 0-9 on the
remote control) until the desired track
appears on the display.
™ The selected track number and
elapsed playing time appear on the
display.
• If you press í once it will skip to the
beginning of the current track and play
the track again.
Note:
– Pressing í during shuffling can only skip
to the beginning of the current track.
Searching for a particular
passage during playback
• Press and hold à or á until the
desired passage is located.
™ The volume will be reduced.
• Play returns to normal when à or á
is released.
3/6/00, 1:26 PM
Programming Tracks
Programming tracks of a loaded CD is
possible when playback is stopped. The
display will indicate the total tracks stored
in the program. Up to 40 tracks can be
stored in the memory in any order. When
40 tracks are stored and you attempt to
store another track, the display will show
"PROGRAM FULL".
1 Load the desired discs in the disc trays.
2 Press PROG to start programming.
™ The
starts flashing.
PROGRAM
™ It will cancel any previously selected
repeat mode.
3 Press the CD (CD 1•2•3) or DISC 1/2/3
button to select the disc.
4 Press í or ë (or Digit 0-9 on the
remote control) to select the desired
track.
5 Press PROG to store the track.
• Repeat steps 3 to 5 to store other discs
and tracks.
6 Press Ç once to end programming.
™ The total number of tracks
programmed and total playing time
appear on the display.
Notes:
– If the total playing time is more than
" 99:59 " or if one of the programmed
tracks has a number greater than 30,
then " --:-- " appears on the display
instead of the total playing time.
3139 116 19721