Toshiba SDK990KU Kullanıcı El Kitabı - Sayfa 13

DVD Oynatıcı Toshiba SDK990KU için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Toshiba SDK990KU 40 sayfaları. Sd7200ku user's guide

Sayfayı Yazdır

Connections

Content of the output for each output jack is shown in the following table and differ depending on the On-Screen Display Setting:

On-Screen Display Setting

Content of output for each output jack

"Video Out"

HDMI Output

Setting

Setting *

Component

Invalid

(Interlaced)

P-Scan

Invalid

(Progressive)

480p

HDMI

720p

1080i

1080p

Note: Both Composite (Video) and Component do not have output when HD JPEG Mode is on

mode. You may view photos (JPEG ) through HDMI connection. To watch disc playback through Composite and Component

output, set HD JPEG Mode to "Off".

* Settings for HDMI output format are performed using the HDMI button on the remote control or HDMI SELECT button on the

front panel.

Notes

• If Auto is selected, it follows preference HDMI aspect ratio of TV.

• Refer to the owner's manual of the connected TV as well.

• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making

any connections.

• If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to this player using a HDMI cable.

• The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is compatible

with, including DVD-Video, Video CD/Super VCD, CD, WMA, MP3 and DivX

• This unit has been designed to be compliant with HDMI (High Definition Multimedia Interface) depending on the component you

have connected. Using a HDMI connection may result in unreliable signal transfers.

• Because HDMI is an evolving technology, it is possible that some devices with an HDMI input may not operate properly with this

DVD player.

• When using HDMI cable, do not connect to other analog video outputs.

• No sound will be output from the HDMI cable if the digital out is not set to PCM.

• HDMI output is only available when the Video Output is set to "HDMI". Otherwise the HDMI button is invalid.

Connecting to Optional Equipment

You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.

• For connection to your TV, see "Connecting to a TV" .

• This section uses the following reference marks.

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Notes

• Do NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby Digital Receiver. This

input on your A/V Receiver is reserved for Laser disc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack

of the DVD player.

• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the "DIGITAL (COAXIAL)" input of a Receiver or Processor.

• Refer to the owner's manual of the connected equipment as well.

• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall

outlet before making any connections.

• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening

level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD player's power cord. If you leave the amplifier power on, the

speakers may be damaged.

HDMI

Video

Component

Output

Composite

480i

Composite

480p

Composite

480p

720p

Composite

480p

1080i

Composite

480p

1080p

Composite

480p

Warning

• When you are connecting (via the COAXIAL DIGITAL AUDIO

OUT jack) an AV decoder that does not have Dolby Digital,

Digital Theater Systems (DTS) or MPEG2 decoding function,

be sure to set "Digital Output" to "PCM" from the on-screen

displays. Otherwise, high volume sound may damage your

hearing as well as the speakers.

• When playing DTS-encoded discs (DVDs and audio CDs),

excessive noise may be output from the analog audio output

jacks. To avoid possible damage to the audio system, you

should take proper precautions when the analog audio output

jacks of the DVD player are connected to an amplification

system. To enjoy DTS Digital Surround™ playback, an external

5.1 channel DTS Digital Surround™ decoder system must be

connected to the COAXIAL DIGITAL AUDIO OUT jack of the

DVD player.

, except 480p video resolution