Toshiba TDP-D1 Kullanıcı El Kitabı - Sayfa 11

Projektör Toshiba TDP-D1 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Toshiba TDP-D1 20 sayfaları. Toshiba dlp data projector tdp-d1 tdp-d2 owner's manual

Sayfayı Yazdır

1. Connection

Turning the power on and off (Continued)

Notes

• The start-up screen will disappear after a moment. You can dismiss the start-up screen

before this by performing any operation. You can also configure the start-up screen not to

appear via the Display setting menu

• The first time you use the projector after purchase, after the start-up screen disappears,

the Language menu is displayed

p.21

I Turning the power off

Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This

message will disappear after a moment. (This operation is no longer valid after the

message disappears.)

Press the ON/STANDBY button again.

The screen turns off, but the internal cooling fan continues to operate for a short while.

Then, the projector goes into standby mode.

When cooling lamp

During internal cooling

FAN

TEMP LAMP

FAN

(Green)

(Green) (Orange)

(Green)

Flashing

During cooling, the LAMP indicator flashes. In this state, the power cannot be

turned back on. In addition, unplugging the power cord or turning off the main

power switch in this state will shorten the life of the lamp.

After the LAMP indicator goes off, the cooling fan continues to operate for a

short while, in order to expel excess internal heat. If you are in a hurry, there is

no problem with unplugging the power cord or turning off the main power switch

in this state.

In standby mode

Note

• The projector consumes about 6W of power in standby. We recommend that you unplug

the power cord or turn off the main power switch if you will not be using the projector for

an extended period.

PRECAUTIONS

• Before unplugging the power cord or turning off the main power switch, make sure that

the LAMP indicator is off. Unplugging the power cord or turning off the main power

switch and cutting off the power while the projector is running or being cooled will

shorten the life of the lamp. However, please unplug the power cord if the projector

locks up or acts abnormally.

• If the power cord is unplugged before cooling is complete, give the lamp time (about 10

minutes) to cool before plugging it back in. If the lamp overheats it may fail to light, and

its lifetime will be shortened.

p.29

After cooling complete

TEMP LAMP

FAN

TEMP LAMP

(Off)

(Orange)

(Off)

(Orange)

Basic operations

Turn on the power.

Turn on the power, following the instructions in "Turning on the power"

Select language (When using for first time).

When the projector is used for the first time after purchase, a message is displayed on

the screen, and the language menu appears. The default language is English.

(If the screen focus is not on the menu, adjust according to step

q Use the

buttons to select the desired

language, and press the

A message displays the selected language.

w Press the

button to erase the message.

Notes

• After the first time the projector is turned on, the Language menu does not appear

upon startup. However, from the Reset menu

Language menu the next time the projector is turned on.

• The language can also be set via the Display setting menu

• This owner's manual assumes that English has been selected.

Place connected device(s) in operating status.

Turn on and boot up connected computers and other devices.

Select "Cancel" or install driver contained in the supplied CD-ROM, when the dialog

box of the Add New Hardware Wizard screen appears on the computer when

connecting a computer. (The supplied CD-ROM contains a driver information file

named TOSHIBA_TDP.inf. Click the Browse button of the dialog box to find and

designate this file.)

Select input.

q Press the INPUT button.

A list of inputs appears on the screen.

w Use the

buttons to select the desired

input, and press the

button.

The picture for the selected input is projected.

p.19

................

English

..............

button.

Français

French

..............

Deutsch

German

................

Italiano

Italian

...............

Español

Spanish

..........

Português

Portuguese

...................

Japanese

.......

Chinese (simplified)

.......

Chinese (traditional)

...................

Korean

select "Reset all" to display the

p.29

Remote

Control panel

Control

LAMP

TEMP

FAN

ON/STANDBY

INPUT

RESIZE OFF

VOL.

VOL.-

AUTO KEYSTONE

AUTO SET

Computer

Y/P

Video

S-video

RESIZE INPUT

INPUT

VOL.+