Toshiba TDP-D2-US Kullanıcı El Kitabı - Sayfa 12

Projektör Toshiba TDP-D2-US için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Toshiba TDP-D2-US 20 sayfaları. Toshiba tdp-d2-us: specifications
Ayrıca Toshiba TDP-D2-US için: Teknik Özellikler (2 sayfalar), Teknik Özellikler (1 sayfalar)

Sayfayı Yazdır

1. Connection

Basic operations (Continued)

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot

adjuster.

q Lift up the front of the projector until

it is at the desired angle, then press

the foot adjuster release button.

The foot adjuster extends. Release the

button to lock the position.

w Turn the foot adjuster to fine-tune

the angle.

e To adjust the horizontal angle, use

the tilt adjuster.

To stow the foot adjuster, hold up the projector while pressing the foot adjuster

release button, then slowly lower the projector will the button depressed.

Adjusting the picture size and focus

q Use the zooming lever to adjust the screen

size.

w Use the focusing ring to adjust the focus.

Adjusting the volume with the

The speaker volume can be adjusted when an audio signal is being input.

Notes

• Note that the lamp characteristics may rarely cause the brightness to fluctuate slightly.

• A lamp is consumable supplies.

If used for extended periods, images will appear dark, and the lamp could burn out. This

is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on

conditions of use.)

• The DMD

is made using extremely advanced technology, but there may be black spots

(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.

Please note that these are not malfunctions.

• Although this projector supports a wide range of RGB signals

supported by this projector (XGA) will be expanded or shrunk, which will affect image

quality slightly. To view high-quality images, it is recommended that the computer's

external output should be set to XGA (1,024 x 768) resolution.

• With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor's display may prevent the images from

displaying properly. If this happens, turn off the computer's LCD display. For information

on how to turn off the LCD display, see the owner's manual of your computer.

• If a signal not supported by the projector is input, the

• If a no signal is being input from the connected device, the

• If an unavailable operation button is pressed, the

buttons

p.36

, any resolutions not

icon will appear.

Using handy features

I Using auto setting (Auto setting)

This function sets up the projector to the optimum state for

each type of the input signal by using simple operations.

Press the AUTO SET button.

The Auto setting menu appears.

Press the AUTO SET button again.

The menu item is automatically adjusted/set.

For computer input, the

processing.

Note

• Auto adjustment/setting may not be performed correctly for input signals other than

those supported by the projector

G Manual adjustment and setting

The menu items vary according to the input type, as shown in the table below.

Use the

the

button when you are finished. The menu disappears.

Input

Computer

Y/P

Video

Video mode

S-video

Control panel

icon will appear during

p.36

p.37

buttons to adjust the items in the table below, then press

Item

Description

Phase

Adjust with

to eliminate flicker.

Frequency

Adjust with

to eliminate periodic patterns and

flickering when many vertical lines appear in the screen.

H-position

Move left

Move right

V-position

Move up

Move down

Phase

Adjust with

to eliminate flicker.

Signal format [

: Enter to setting mode]

of the following]

[Apply:

480i(525i)@60Hz/480p(525p)@60Hz/

576i(625i)@50Hz/576p(625p)@50Hz/

720p(750p)@60Hz/720p(750p)@50Hz/

1080i(1125i)@60Hz/1080i(1125i)@50Hz/

1035i(1125i)@60Hz/1152i(1250i)@50Hz

[

: Enter to setting mode]

of the following]

[Apply:

NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43

Remote

Control

LAMP

TEMP

FAN

ON/STANDBY

LASER

CALL

ON/STANDBY

INPUT

MUTE

FREEZE

AUTO

KEYSTONE

SET

PAGE

DOWN

VOL.

AUTO KEYSTONE

AUTO SET

[

: Select one

]

[

: Select one

]