Toshiba TDP-TW355 Kullanıcı El Kitabı - Sayfa 25

Projektör Toshiba TDP-TW355 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Toshiba TDP-TW355 47 sayfaları. Data projector
Ayrıca Toshiba TDP-TW355 için: Teknik Özellikler (2 sayfalar), Kullanıcı El Kitabı (48 sayfalar)

Sayfayı Yazdır
Toshiba TDP-TW355 Kullanıcı El Kitabı
Using the menus (Continued)

Displaying Information (Status display)

This displays information about the input signal, lamp use time, LAN connection status,
etc.
Item
Description
Projector
Input
Input source name
[Note 1]
Mode name
RGB input mode
Resolution
Resolution (in dots)
Frequency
Sync frequency
Sync
Sync signal polarity
Signal format
Y/P
/P
signal format
B
R
Video mode
Color method of video signal
Lamp time
Time of lamp use
[Note 3]
Lamp reset count The count for lamp replacement
Total time
The total time that this projector is
used.
Version
Firmware version
[Note 4]
Wired LAN
Connection status Displays connection status of LAN.
IP address
Displays the IP address.
Subnet mask
Displays numeric value of subnet
mask.
Gateway
Displays numeric value of gateway.
MAC address
Displays MAC address of the
projector.
[Note 5]
PJLink class
PJLink version
Notes
p.88
1: The mode of supported RGB signals
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult
with a store about getting a TLPLW14 replacement lamp (sold separately) prepared.
4: [Version] shows the version of the projector's internal control program. This version is referred
to for customer service, etc.
5: In case that "------" appears for MAC address, please contact your dealer.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again. The information regarding
wired LAN is refreshed every time it is displayed.
"Yes": displayed, "No": not displayed
Video Wireless/ USB
Computer Y/P
/P
B
R
S-video Card memory
Yes
Yes
Yes
Yes
Yes
No
No
No
Yes
No
No
No
Yes
No
No
No
[Note 2]
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
is shown.
48

How to use the PC card slot

The wireless LAN PC card enables you to connect the projector wirelessly with a personal
computer that supports IEEE802.11b/g based wireless LAN.
communication between all the computers based on IEEE802.11b/g and this projector is
not guaranteed.) You can also use a commercially available memory PC card to project
JPEG image files using this projector.
or mounting a PC card.
Mounting a PC card
q Remove the slot cover.
Yes
Press lightly on the circle ("O") while
No
sliding the cover in the direction of the
No
arrow.
No
No
No
No
Yes
Yes
Yes
Slot cover
Yes
w Insert the PC card.
Yes
After making sure of the card orienta-
Yes
tion, press it in firmly until it stops.
Yes
Yes
Yes
Yes
If CARD indicator turns red
Press the RESET switch with a thin pin or
similar implement (it is at the bottom of a
recess).
(Please note that
p.51
p.58
Please follow the steps below when removing
Removing a PC card
q Look at CARD indicator.
If it is off, proceed to step r.
CARD indicator
UNMOUNT button
w Press the UNMOUNT button.
Begins processing for PC card removal.
e Wait until CARD indicator goes
out.
Never remove the PC card while lit.
Doing so could damage the PC card or
corrupt your data.
PC Card
r Press the Eject button.
CARD indicator
RESET
switch
49
Eject button