Toshiba TDP-WX5400 Kullanıcı El Kitabı - Sayfa 30
Projektör Toshiba TDP-WX5400 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Toshiba TDP-WX5400 42 sayfaları. Toshiba tdp-wx5400: user guide
Ayrıca Toshiba TDP-WX5400 için: Kurulum Kılavuzu (16 sayfalar)
Sayfayı Yazdır
Using the Setting menus (Continued)
The Setting 3 menu
Item p q
Select the power on mode. Press
Power on
Manual—the projector must be powered on manually using the control panel or remote.
Auto—the projector powers on automatically when the main power switch is turned on.
Sets the time to wait for the power to be turned off after the last operation is made with
No signal
no input signal. Press
and select the lamp interval using p q.
power off
Off/5 min./10 min./20 min./30 min.
Screen trigger Enable or disable the screen trigger function. Press
Select the desired fan mode. Press
Fan mode
Standard/High
Select the image source that the projector will search for automatically on startup. Press
Default input
and select the default input device using p q.
select
Last source/Auto./Computer1/Computer2/Computer3/Y-PB-PR/Video/S-video
Video: Press
and select the default video mode using p q.
Auto./NTSC/PAL/SECAM
Video mode
S-video: Press
and select the default S-video mode using p q.
Auto./NTSC/PAL/SECAM
Enable or disable the onscreen warning and informational messages. Press
Message
or Off using p q.
Set the interval between filter cleaning warning messages. Press
Filter warning
interval using p q.
Off/100H/200H/500H/1000H
Set the search mode. Press
Search mode
Standard/Fine
Note
•
If [Power on] is set to [Auto] and there is a power outage, the projector will come on
once power is restored.
•
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,200
meters above sea level).
Do not set Fan mode to [High] when using the projector at a lower altitude."
Description
and select the power on mode using p q.
and select On or Off using p q.
and select the fan mode using p q.
and select On
and select the desired
and select the desired search mode using p q.
58
Using the Status display screen
The Status display screen provides a quick access to the detailed information on projector status.
The Status display menu contains four distinct tabs; Usage time, Input, Network, and Version.
Note
•
Information on the Status display screens is read only.
The Usage time screen
Item p q
Lamp1
Displays the Lamp1 life remaining as a percentage.
Lamp2
Displays the Lamp2 life remaining as a percentage.
Lamp1 time Displays the Lamp1 total usage in hours.
Lamp2 time Displays the Lamp2 total usage in hours.
PJ time
Displays the projector's total usage in hours.
Filter time
Displays the filter total usage in hours.
Note
Displays [Lamp 1/2 time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000
hours, consult with a dealer about getting replacement for:
TLPLW25 for TDP-WX5400 (sold separately).
The Input screen
Item p q
Input name Displays the input terminal that is currently being used.
Signal
Displays the signal name of the currently being used.
H-sync. freq. Displays horizontal frequency in KHz
V-sync. freq. Displays vertical frequency in Hz
Video mode Displays video type, if present.
Sync
Displays synchronization type.
Sync polarity Displays sychronization polarity.
Scan type
Displays the scan type.
Description
Description
59