Toshiba TLP TLP-X2000 Kullanıcı El Kitabı - Sayfa 22
Projektör Toshiba TLP TLP-X2000 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Toshiba TLP TLP-X2000 31 sayfaları. Brochure
Ayrıca Toshiba TLP TLP-X2000 için: Broşür ve Teknik Özellikler (2 sayfalar), Teknik Özellikler (1 sayfalar)
Using the menus (Continued)
■ The default setting menu
This menu shows placement status and other settings.
Default setting 1 menu
Item
No signal
Set the time to wait for the power to be turned off after the last
power off
operation is made with no input signal.
Auto input
Set whether the input with signals is only selected or not.
search
Beep
Beep when operation is made.
Sets whether to turn on the power when the ON/STANDBY button is
Power on
pressed (Manual), or when the power cord is plugged in (Auto).
Sets the lamp power.
Lamp power
Detailed description
[Auto input search]
[On]: Automatically searches the signals that
can be projected, and switches input
from the connected device that outputs
the video signals each time the INPUT
button is pressed. The input from the
connected device that outputs no video
signals is skipped.
[Off]: Displays the Input select menu.
Toggle with
buttons and press
button. (The input without signals can be
selected.)
[Power on]
Note that if [Power on] is set to [Auto], then if the power is supplied when restored
after a power outage, the projector will come on.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
Description
Off (not turned off)
30 min.
On
On
Manual
Low
Standard
Input select menu
Input select
Computer 1
Y/P
/P
1
B
R
Computer 2
Y/P
/P
2
B
R
Video
S-video
/
shows whether signal is
input or not.
42
Default setting 2 menu
Item
Projection
mode
Fan mode
Remote
control
Off
Off
Key lock
Auto
Reset all
Password
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan
noise gets louder.) Set this option to use the projector, for example, at high altitude
(over 1,500 meters above sea level).
• Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the
remote control do not match.
Remote control code setting for remote control
Remove the battery cover and set the same remote control code switch as the
projector.
p.16 p.17
Description
Sets projection mode in accordance with Placement Style.
(Standard)
(Rear)
Sets the cooling fan speed.
When two or more projectors are used and controlled by the remote
control respectively, this menu sets the code for the projector and the
remote control.
[
or
: Enter setting mode]
[
[
:Confirm]
[
:Select OK to end]
Press [Cancel] to return.
Lock the control panel buttons.
[
or
: Enter setting mode]
[
[
:Confirm]
[
:Select OK to end]
Press [Cancel] to return.
Press
. (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password setting
p.33
(Use a screwdriver with thin tip to set.)
43
p.22
(Ceiling)
(Rear ceiling)
Standard
High
: Select from 1, 2, 3, 4]
: Select On/Off]
Yes
No