Dimplex Courchevel Talimatlar - Sayfa 4

Soba Dimplex Courchevel için çevrimiçi göz atın veya pdf Talimatlar indirin. Dimplex Courchevel 5 sayfaları.
Ayrıca Dimplex Courchevel için: Manuel (4 sayfalar), Talimatlar (4 sayfalar)

Sayfayı Yazdır

- Club, CLB20R

- Courchevel, CVL20

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Important Safety Advice

When using electrical appliances, basic precautions should

always be followed to reduce the risk of fire, electrical shock

and injury to persons, including the following:

If the appliance is damaged, check with the supplier before

installation and operation.

Do not use outdoors.

Do not use in the immediate surroundings of a bath, shower

or swimming pool.

Do not locate the heater immediately below a fixed socket

outlet or connection box.

Do not cover the heater. Do not place material or garments

on the heater, or obstruct the air circulation around the heater,

for instance by curtains or furniture, as this could cause

overheating and a fire risk.

This appliance is not intended for use by children or other

persons without assistance or supervision if their physical,

sensory or mental capabilities prevent them from using it

safely. Children should be supervised to ensure that they do

not play with the appliance. Do not use this heater in series

with a thermal control, a program controller, a timer or any

other device that switches on the heat automatically, since a

fire risk exists when the heater is accidentally covered or

displaced.

Ensure that furniture, curtains or other combustible material

are positioned no closer than 1 metre from the heater.

In the event of a fault unplug the heater.

Unplug the heater when not required for long periods.

Although this heater complies with safety standards, we do

not recommend its use on deep pile carpets or on long hair

type of rugs.

The appliance must be positioned so that the plug is

accessible.

If the supply cord is damaged it must be replaced by the

manufacturer or service agent or a similarly qualified person

in order to avoid a hazard.

Keep the supply cord away from the front of the heater.

This heater is not equipped with a device to control the

room temperature. Do not use this heater in small rooms

when they are occupied by persons not capable of leaving

the room on their own, unless constant supervision is

provided.

Warning: In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this appliance must not be

supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on

and off by the utility.

General

Unpack the heater carefully and retain the packaging for possible

future use, in the event of moving or returning the fire to your supplier.

These models are designed to be free standing and are normally

positioned against a wall.

The fire incorporates a flame effect, which can be used with or without

heating, so that the comforting effect may be enjoyed at any time of

the year. Using the flame effect on its own only requires little electricity.

A choice of 1kW or 2kW heat output is provided by the fan heater,

which is located at the bottom of the unit.

Before connecting the heater check that the supply voltage is the

same as that stated on the heater.

Please note: Used in an environment

low, it may be possible to hear a sound which is related to the operation

of the flame effect. This is normal and should not be a cause for

concern.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED.

This heater must be used on an AC ~ supply only and the voltage

marked on the heater must correspond to the supply voltage. Before

switching on, please read the safety warnings and operating

instructions.

where background noise is very

Controls

- see Fig. 2

These switches provide a choice of heat settings, The appliance is in

standby mode when the mainslead is plugged in. This is indicated by

the

red

neon

behind

The two selector switches are in the ON position when the side with

the markings on (i.e. I, or II) is pushed in.

Selector switch 1 (0)

Controls the electricity supply to the

heater and flame effect. Press for 'ON' and

'Standby'. If both selector switches 2 and 3

are in the OFF position, the product works

on flame effect only.

Selector Switch 2 (I)

Provides 1kW heat output

Selector Switch 3 (II)

Provides 2kW output with switch 2

Remote

control - see Fig. 6

The maximum range of use is ~ 15metres.

Warning: It takes time for the receiver to respond to the transmitter.

Do not press the buttons more than once within two seconds for correct

operation.

Battery information - see Fig. 6

Slide open the battery cover on the back of the remote control

Install AAA batteries into the remote control

Replace the battery cover.

Discard leaking batteries

Dispose of batteries in the proper manner according to provincial and

local regulations.

Any battery may leak electrolyte if mixed with a different battery type,

if inserted incorrectly, if all the batteries are not replaced at the same

time, if disposed of in a fire, or if an attempt is made to charge a

battery not intended to be recharged.

Lamp Replacement - see Fig. 3, Fig. 4 and Fig. 5

The lamps are located behind the back panel. To gain access to the

lamps, the screws indicated in Fig. 3 which secure the back panel,

must be removed.

Remove and slide out panel as indicated on Fig. 4.

Remove the defective lamp by unscrewing it as shown in Fig. 5.

Replace with a 60W E14 SES Clear candle lamp. Take care not to

over-tighten the lamp.

Refit the back panel and secure with the screws.

Thermal Safety Cut-out

The built-in overheat cut-out switches off the appliance automatically

in the event of a fault. If this occurs switch off the appliance or

disconnect the mains plug from the socket. After a short cooling down

phase, the appliance is ready for use again. If the fault should occur

again, see your local dealer.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY

BEFORE ATTEMPTING ANY MAINTENANCE.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY

BEFORE CLEANING THE HEATER.

For general cleaning use a soft clean duster – never use abrasive

cleaners. The glass viewing screen should be cleaned carefully with

a soft cloth. DO NOT use proprietary glass cleaners.

To remove any accumulation of dust or fluff the soft brush attachment

of a vacuum cleaner should occasionally be used to clean the outlet

grille of the fan heater.

Recycling

For electrical products sold within the European

Community.

At the end of the electrical products useful life it should

not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or

retailer for recycling advice in your country.

the

flame

effect

screen.