Dimplex CDFI1000-PRO Servis Kılavuzu - Sayfa 4

Elektrikli Isıtıcı Dimplex CDFI1000-PRO için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Dimplex CDFI1000-PRO 18 sayfaları.

Sayfayı Yazdır

Remote Control

The tethered controller serves as the bluetooth receiver for

communication with the remote, and must be connected for

remote operation of the unit. It can also be used in the same

manner as the remote.

The tethered controller must be connected to the unit and On/

Off Switch must be in the 'ON' ( I ) position in order for the

remote to operate.

NOTE: To operate correctly the remote control must be

synchronized with the unit.

Remote Control Synchronization / Pairing

In order for the remote control to communicate with the unit

the bluetooth must be setup, as outlined below:

1. Verify that the tethered controller is connected correctly

and that the plug is inserted all the way.

2. Place the On/Off Switch (Figure 1A) in the ON ("I")

position. The red light on the tethered controller will be

illuminated.

3. Press the Standby button to activate the flame effect.

4. Press the Bluetooth synchronization button on the

Primary controls (left side).

5. The unit will begin to beep and turn the lights ON and

OFF every 2 ½ seconds to indicate that the unit is in

synchronization mode.

6. Within 20 seconds of pressing the blue tooth button, press

any button on the remote control (Figure 1).

NOTE: You will have only 20 seconds to perform this last

step. Failure to do so will result in these steps needing to

be followed again.

7. If the synchronization was successful the LED's will blink

5 times and beep 5 times then the unit will go to Standby.

This will synchronize the remote control and the tethered

controller.

NOTE: It is possible to synchronize up to 5 units to one

remote control.

Battery Replacement

To replace the battery:

1. Slide battery cover open on

the remote control (Figure 3).

2. Install two 1.5 Volt (AAA) bat-

tery in the battery holder.

3. Close the battery cover.

Battery must be recycled

or disposed of properly.

Check with your Local

Authority or Retailer for recycling

advice in your area.

Figure 3

Battery Cover

Maintenance

WARNING: Disconnect power before attempting any main-

tenance or cleaning to reduce the risk of fire, electric shock

or damage to persons.

Filling the water tank (Refillable bottle)

When the water tank is low, the flame effect will shut off and the

unit will emit an audible beep and continuously blink twice every

ten seconds. To refill the bottle(s), follow these steps.

1. Gently remove the top tray and place it carefully on the

ground.

2. Turn the On/Off switch to the off position (0) (Figure 1A)

3. Remove the refill container by lifting upwards and outwards.

4. Refill the container with tap water.

NOTE: Normal tap water can be used in the Optimyst

long as the tap water is not considered to be hard water.

In the event your tap water is hard, you may use softened

water or distilled water with ⅛ tsp. of salt (0.5 mL) added to

the water reservoir. (The use of additional salt should only

be when you notice that the unit is not producing mist as

expected.)

5. Screw the cap back on, do not overtighten.

6. Return the refill container to the sump, with the tank cap fac-

ing down and the flat side of the tank facing outward.

7. Turn the On/Off switch to the off position (I) . (Figure 1A)

8. Gently place the top tray back into position.

If you do not intend on using the unit for longer than 2 weeks,

empty and drain the unit of water, and dry all of the water con-

taining components.

Transducer Replacement

After prolonged usage the ability for the unit to produce mist

may become reduced. When this occurs the replacement of

the transducer may be required. This unit comes with 2 addi-

tional transducers, located behind the right module, which can

installed when this occurs.

NOTE: There is a small tab that holds the transducer in

place, that needs to be released before it can be removed.

Cleaning

It is recommended that the top cover assembly, sump and

transducer are cleaned with soap and water on a biweekly

basis.

CAUTION: Do not put plastic components in the dishwasher.

Filter Cleaning

The air filters can be removed and gently rinsed with water to

clean and dried on a towel before reinstalling.

NOTE: Replace the filter so that the course black filter is fac-

ing the back of the unit.

Surface Cleaning

Use a warm damp cloth only to clean surfaces of the unit. Do

not use abrasive cleaners.

NOTE: If you need to move the unit ensure that all of the

components that contain water have been emptied before

relocating.

Servicing

Except for installation and cleaning described in this manual,

an authorized service representative should perform any other

servicing.