Aeon Labs Z-Stick Series 2 Kullanım Talimatları

Adaptör Aeon Labs Z-Stick Series 2 için çevrimiçi göz atın veya pdf Kullanım Talimatları indirin. Aeon Labs Z-Stick Series 2 2 sayfaları. 2-wave usb adapter

Sayfayı Yazdır

_________________________________________________________________

http://waterheatertimer.org/How-to-wire-Intermatic-CA3750.html

Aeon Labs Z-Stick Series 2

(Z-Wave USB Adapter)

Introduction:

The Aeon Labs Z-Stick S2 (Series 2) is a self-powered Z-Wave

USB adapter with remote network creation capabilities

(independent

from

external

power

microprocessor). By being able to remotely include/remove

Z-Wave devices, this greatly simplifies Z-Wave network

installation. When connected to a host controller (via USB),

it enables the host controller to take part in the Z-Wave

Network.

The Z-Stick S2 is also device firmware upgradeable by the

end consumer. This enables the product to always have the

latest Z-Wave protocol, capabilities and commands.

By taking advantage of the Z-Wave mesh network,

commands can be routed to their destination via

intermediary "listening" Z-Wave products. Products that

are Z-Wave certified can be used and communicate with

other Z-Wave certified devices.

- 1 -

Operating instructions:

The Z-Stick operates in three distinct modes: Inclusion-

Mode, Removal-Mode and SerialAPI-Mode. Both

Inclusion-Mode and Removal-Mode require the Z-Stick to

be unplugged from the USB connector of the host, while

SerialAPI-Mode requires that the Z-Stick to be plugged into

the USB connector of the host. Software drivers for the

Silabs CP2102 may need to be installed for the Z-Stick to be

recognized on some computers. (drivers can be found at

http://www.aeon-labs.com/support) .

Inclusion-Mode : Adding/Including Z-Wave Devices

•

into the Z-Wave Network

To initiate Inclusion-Mode, unplug the Z-Stick

from the USB connector and then tap the

button. (The LED will blink slowly.)

Note: While in Inclusion-Mode, the Z-Stick is in

perpetual add/inclusion. There is no need to

press the button on the Z-Stick again to include

each new device.

To include a new Z-Wave device into the

network, simply go to the device with the Z-

Stick and press the button on the device you

wish to include. (The LED on the Z-Stick will

and

host

blink fast during a network neighbor discovery

and stay solid for 3 seconds to indicate

successful inclusion of the device into the

network.)

The LED will then return to blinking slowly,

indicating readiness for further device inclusions.

Repeat step 2 for each device as you wish to

include.

Tap the Z-Stick button to turn it off.

- 2 -

Removal-Mode : Deleting/Removing/Excluding Z-

•

Wave Devices from the Z-Wave Network

To initiate Removal-Mode, unplug the Z-Stick

from the USB connector. Then press and hold

down the button for approximately 3 seconds.

(The LED will transition from blinking slowly to

blinking fast.)

Note: While in Removal-Mode, the Z-Stick is in

perpetual removal/exclusion where it will

remove Z-Wave devices from the networks they

are currently paired to. There is no need to

press the button on the Z-Stick again to exclude

each device.

To remove a Z-Wave device from the network,

simply go to the device with the Z-Stick and

press the button on the device you wish to

remove.

(The LED on the Z-Stick will

immediately stay solid for 3 seconds to indicate

successful removal from the network.)

The LED will then return to blinking fast,

indicating

readiness

for

further

exclusions. Repeat step 2 for each device as

you wish to exclude.

Tap the Z-Stick button to turn off.

SerialAPI-Mode : Allowing a Host Processor To Take

•

Control of the Z-Stick and Take Part in the Z-Wave

Network

To initiate SerialAPI-Mode, plug the Z-Stick into

the USB connector of the host.

Note: While in SerialAPI-mode, the Z-Stick is

always listening (it is awake and always in RX

receive mode) for instructions and acts as a Z-

Wave adapter and responds to commands sent

through USB by the host processor software.

Note: Pressing the Z-Stick button will not have

any effect while in SerialAPI-Mode.

- 3 -

Other Functions:

•

Factory reset on the Z-Stick: This must be done

•

through the host software which takes control

of the Z-Stick USB adapter while the Z-Stick is in

SerialAPI-Mode. Please consult the instruction

manual of the host software to perform a

network reset (i.e. factory reset on the Z-Stick).

This function can only be preformed via the

host software.

Add the Z-Stick to a pre-existing Z-Wave

•

network: This must be done through the host

software which takes control of the Z-Stick USB

adapter while the Z-Stick is in SerialAPI-Mode.

Please consult the instruction manual of the

host software to add the Z-Stick to a pre-

existing Z-Wave network (i.e. "Learn", "Sync",

"Add as Secondary Controller", etc.).

function can only be preformed via the host

software.

device

Upgrading the Z-Stick with the Latest Software

•

Download the Aeon Labs Z-Stick upgrade

software at http://www.aeon-

labs.com/Spport and run the downloaded

program.

Follow the on screen instructions to

complete installation.

- 4 -

This