Pioneer AVH-X5500BT Kurulum Kılavuzu - Sayfa 3

Araç Alıcısı Pioneer AVH-X5500BT için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer AVH-X5500BT 41 sayfaları. Dvd rds av receiver

Sayfayı Yazdır

Connecting the units

Connecting the power cord

Navigation system

(AVIC-F220 (sold

separately))

26 pin cable (Supplied with navigation unit)

Please contact your dealer to

Insert the 26 pin cable in the direction

inquire about the connectable

indicated in the figure.

navigation unit.

Note:

Depending on the kind of vehicle,

the function of 2* and 4* may be

different. In this case, be sure to

connect 1* to 4* and 3* to 2*.

Yellow (2*)

Yellow (1*)

Back-up

Connect to the constant 12 V

(or accessory)

supply terminal.

Red (4*)

Red (3*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

Orange/white

Connect to lighting switch terminal.

Black (chassis ground)

Connect to a clean, paint-free metal location.

ISO connector

Note:

In some vehicles, the ISO connector may be divided into

two. In this case, be sure to connect to both connectors.

This product

Fuse (10 A)

Antenna input

DAB antenna input

RGB input

(AVH-X3500DAB only)

AUX jack (3.5 ø)

To receive DAB signals,

Use a mini plug

connect a DAB antenna

cable to connect

(AN-DAB1) sold

with auxiliary

separately to the unit.

device.

Connect leads of the same

color to each other.

Speaker leads

White:

Front left

White/black:

Front left

Gray:

Front right

Gray/black:

Front right

Rear left  or subwoofer

Green:

Rear left  or subwoofer

Green/black:

Rear right  or subwoofer

Violet:

Rear right  or subwoofer

Violet/black:

Connecting the units

4 m

Microphone (Function of AVH-X5500BT/AVH-X3500DAB/AVH-X2500BT)

Microphone input (Function of AVH-X5500BT/AVH-X3500DAB/AVH-X2500BT)

Wired remote input

Hard-wired remote control adapter can be connected (sold separately).

Violet/white

Of the two lead wires connected to the back lamp, connect the one in which the

voltage changes when the gear shift is in the REVERSE (R) position. This connection

enables the unit to sense whether the car is moving forwards or backwards.

Yellow/black

If you use an equipment with Mute function, wire this lead to the Audio Mute lead on

that equipment. If not, keep the Audio Mute lead free of any connections.

Connection method

1. Clamp the lead.

Note:

· The position of the parking brake switch depends on the vehicle model. For details,

consult the vehicle Owner's Manual or dealer.

Light green

Used to detect the ON/OFF status of the parking brake. This lead

must be connected to the power supply side of the parking brake

switch.

Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

Blue/white (6*)

Blue/white (5*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO

connector will differ depending on

the type of vehicle. Connect 5* and

6* when Pin 5 is an antenna control

type. In another type of vehicle,

never connect 5* and 6*.

2. Clamp firmly with

needle-nosed pliers.

Parking brake

switch

Power supply side

Ground side

Notes:

· Change the initial setting of this unit (refer to the Operation Manual).

The subwoofer output of this unit is monaural.

· When using a subwoofer of 70 W (2 Ω) , be sure to connect with Violet

and Violet/black leads of this unit. Do not connect anything to Green

and Green/black leads.

Section