Pioneer DEH-1550B Kurulum Kılavuzu - Sayfa 4
Araç Alıcısı Pioneer DEH-1550B için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer DEH-1550B 6 sayfaları. Deh-1550; deh-1550b
Sayfayı Yazdır
1. This Product
2. Rear output
4. Fuse
3. Antenna jack
6. Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300 mA
12 V DC).
9. Yellow
To terminal always supplied with
power regardless of ignition
switch position.
10. Red
To electric terminal controlled by
ignition switch (12 V DC)
ON/OFF.
11. Black (ground)
To vehicle (metal) body.
25. With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
5. Connecting cords with RCA
pin plugs (sold separately)
8. System remote control
+
+
12. Rear speaker
12. Rear speaker
≠
≠
13.
Perform these connections when using
the optional amplifier.
19. Gray
17. White
+
+
14. Front speaker
14. Front speaker
≠
≠
18. White/black
20. Gray/black
15. Left
21. Green
23. iolet
V
+
+
12. Rea speaker
12.
r
Rear speaker
≠
≠
22. Green/black
24. Violet/black
Connecting the Units
Note:
•
This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
•
To avoid shorts in the electrical system, be sure
to disconnect the ≠ battery cable before begin-
ning installation.
7. Power amp
•
Refer to the owner's manual for details on con-
(sold separately)
necting the power amp and other units, then
make connections correctly.
•
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
•
Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
•
Don't pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
•
Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
•
Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
•
When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
•
Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
or the left and right ≠ speaker leads are com-
mon.
•
Speakers connected to this unit must be high-
power types with minimum rating of 50W and
impedance of 4 to 8 ohms. Connecting speakers
16. Right
with output and/or impedance values other than
those noted here may result in the speakers
catching fire, emitting smoke, or becoming dam-
aged.
•
When this product's source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp's system
remote control or the car's Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
Fig. 8
car features a glass antenna, connect to the anten-
na booster power supply terminal.
∏ qJAë
Connection Diagram (Fig. 8)
•
When an external power amp is being used with
this system, be sure not to connect the blue/white
1. This Product
lead to the amp's power terminal. Likewise, do
2. Rear output
not connect the blue/white lead to the power ter-
3. Antenna jack
minal of the auto-antenna. Such connection could
4. Fuse
cause excessive current drain and malfunction.
5. Connecting cords with RCA pin plugs (sold sepa-
•
To avoid short-circuiting, cover the disconnected
rately)
lead with insulating tape. Especially, insulate the
6. Blue/white
unused speaker leads without fail. There is a pos-
To system control terminal of the power amp or
sibility of short-circuiting if the leads are not
Auto-antenna relay control terminal
insulated.
(max. 300 mA 12 V DC).
•
If this unit is installed in a vehicle that does not
7. Power amp (sold separately)
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
8. System remote control
nected to a terminal coupled with ignition switch
9. Yellow
ON/OFF operations. If this is not done, the vehi-
To terminal always supplied with power regard-
cle battery may be drained when you are away
less of ignition switch position.
from the vehicle for several hours.
10. Red
To electric terminal controlled by ignition switch
(12 V DC) ON/OFF.
11. Black (ground)
To vehicle (metal) body.
12. Rear speaker
13. Perform these connections when using the
optional amplifier.
14. Front speaker
ACC position
No ACC position
•
The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
•
Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
Installation manuals of both products and con-
nect cords that have the same function.
<ENGLISH>
15. Left
16. Right
17. White
18. White/black
19. Gray
20. Gray/black
21. Green
22. Green/black
23. Violet
24. Violet/black
25. With a 2 speaker system, do not connect anything
to the speaker leads that are not connected to
speakers.