Pioneer DEH-P3370XM UC Kurulum Kılavuzu

Araç Alıcısı Pioneer DEH-P3370XM UC için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer DEH-P3370XM UC 4 sayfaları. Pioneer deh-p3370xm: install guide

Sayfayı Yazdır

DEH-P3370XM

This product conforms to CEMA cord colors.

Printed in Japan

<CRB1735-A> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

• When an external power amp is being used with

negative grounding. Before installing it in a recre-

this system, be sure not to connect the blue/white

ational vehicle, truck or bus, check the battery

lead to the amp's power terminal. Likewise, do not

voltage.

connect the blue/white lead to the power terminal

• To avoid shorts in the electrical system, be sure to

of the auto-antenna. Such connection could cause

disconnect the ≠ battery cable before beginning

excessive current drain and malfunction.

installation.

• To avoid short-circuiting, cover the disconnected

• Refer to the owner's manual for details on con-

lead with insulating tape. Especially, insulate the

necting the power amp and other units, then make

unused speaker leads without fail. There is a possi-

connections correctly.

bility of short-circuiting if the leads are not insulat-

• Secure the wiring with cable clamps or adhesive

ed.

tape. To protect the wiring, wrap adhesive tape

• To prevent incorrect connection, the input side of

around them where they lie against metal parts.

the IP-BUS connector is blue, and the output side

• Route and secure all wiring so it cannot touch any

is black. Connect the connectors of the same colors

moving parts, such as the gear shift, handbrake and

correctly.

seat rails. Do not route wiring in places that get

• If this unit is installed in a vehicle that does not

hot, such as near the heater outlet. If the insulation

have an ACC (accessory) position on the ignition

of the wiring melts or gets torn, there is a danger of

switch, the red lead of the unit should be connected

the wiring short-circuiting to the vehicle body.

to a terminal coupled with ignition switch ON/OFF

• Don't pass the yellow lead through a hole into the

operations. If this is not done, the vehicle battery

engine compartment to connect to the battery. This

may be drained when you are away from the vehi-

will damage the lead insulation and cause a very

cle for several hours. (Fig. 1)

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit and the fuse hold-

ACC position

er.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• Speakers connected to this unit must be high-

• The black lead is ground. Please ground this lead

power types with minimum rating of 50 W and

separately from the ground of high-current prod-

impedance of 4 to 8 ohms. Connecting speakers

ucts such as power amps.

with output and/or impedance values other than

If you ground the products together and the ground

those noted here may result in the speakers catch-

becomes detached, there is a risk of damage to the

ing fire, emitting smoke, or becoming damaged.

products or fire.

• When this product's source is switched ON, a con-

• Cords for this product and those for other prod-

trol signal is output through the blue/white lead.

ucts may be different colors even if they have the

Connect to an external power amp's system remote

same function. When connecting this product to

control or the car's Auto-antenna relay control ter-

minal (max. 300 mA 12 V DC). If the car features

another product, refer to the supplied Installation

a glass antenna, connect to the antenna booster

manuals of both products and connect cords that

have the same function.

power supply terminal.

Connecting the Tuner Unit (Fig. 2)

IP-BUS Input

(Blue)

Power Supply

This Unit

No ACC position

Fig. 1

To IP-BUS Input

(Blue)

Fuse holder

Multi-CD player

(sold separately)

IP-BUS Output

(Black)

Antenna Input

Yellow (Satellite)

Black

Green

(Terrestrial)

6 m

Antenna Unit

(AN-90XM)

IP-BUS cable

(sold separately)

To Head Unit

(Refer to Fig. 3.)

Yellow

To terminal always supplied with power

regardless of ignition switch position.

Black (ground)

To vehicle (metal) body.

Fig. 2