Pioneer Super Tuner III DEH-P930 Kurulum Kılavuzu

Araç Alıcısı Pioneer Super Tuner III DEH-P930 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer Super Tuner III DEH-P930 6 sayfaları. Pioneer deh-p930: install guide

Sayfayı Yazdır

1. Montage DIN Avant/Arrière

DEH-P930

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Japan

Imprimé au Japon

<CRD3446-A> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

• When an external power amp is being used with

negative grounding. Before installing it in a recre-

this system, be sure not to connect the blue/white

ational vehicle, truck, or bus, check the battery

lead to the amp's power terminal. Likewise, do not

voltage.

connect the blue/white lead to the power terminal

• To avoid shorts in the electrical system, be sure to

of the auto-antenna. Such connection could cause

disconnect the ≠ battery cable before beginning

excessive current drain and malfunction.

installation.

• To avoid short-circuiting, cover the disconnected

• Refer to the owner's manual for details on con-

lead with insulating tape. Especially, insulate the

necting the power amp and other units, then make

unused speaker leads without fail. There is a possi-

connections correctly.

bility of short-circuiting if the leads are not insulat-

• Secure the wiring with cable clamps or adhesive

ed.

tape. To protect the wiring, wrap adhesive tape

• To prevent incorrect connection, the input side of

around them where they lie against metal parts.

the IP-BUS connector is blue, and the output side

• Route and secure all wiring so it cannot touch any

is black. Connect the connectors of the same colors

moving parts, such as the gear shift, handbrake,

correctly.

and seat rails. Do not route wiring in places that

• If this unit is installed in a vehicle that does not

get hot, such as near the heater outlet. If the insula-

have an ACC (accessory) position on the ignition

tion of the wiring melts or gets torn, there is a dan-

switch, the red lead of the unit should be connected

ger of the wiring short-circuiting to the vehicle

to a terminal coupled with ignition switch ON/OFF

body.

operations. If this is not done, the vehicle battery

• Don't pass the yellow lead through a hole into the

may be drained when you are away from the vehi-

engine compartment to connect to the battery. This

cle for several hours. (Fig. 1)

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

ACC position

No ACC position

the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• If the RCA pin jack on the unit will not be used, do

• The black lead is ground. Please ground this lead

not remove the caps attached to the end of the con-

separately from the ground of high-current prod-

nector.

ucts such as power amps.

• Speakers connected to this unit must be high-

If you ground the products together and the ground

power types with minimum rating of 50 W and

becomes detached, there is a risk of damage to the

impedance of 4 to 8 ohms. Connecting speakers

products or fire.

with output and/or impedance values other than

those noted here may result in the speakers catch-

• Cords for this product and those for other prod-

ing fire, emitting smoke, or becoming damaged.

ucts may be different colors even if they have the

• When this product's source is switched ON, a con-

same function. When connecting this product to

trol signal is output through the blue/white lead.

another product, refer to the supplied Installation

Connect to an external power amp's system remote

manuals of both products and connect cords that

control or the car's Auto-antenna relay control ter-

have the same function.

minal (max. 300 mA 12 V DC). If the car features

a glass antenna, connect to the antenna booster

power supply terminal.

Antenna jack

15 cm

Refer to handsfree telephone

unit's manual (sold separately).

This Product

MIC terminal

TEL terminal

15 cm

IP-BUS input (Blue)

Multi-CD player

(sold separately)

IP-BUS cable

Yellow/black

If you use a cellular telephone,

connect it via the Audio Mute lead on

the cellular telephone. If not, keep the

Audio Mute lead free of any

connections.

Yellow

Fuse holder

To terminal always supplied with

Fig. 1

power regardless of ignition switch

position.

Red

Fuse resistor

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

Fuse resistor

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Subwoofer output

(SUBWOOFER OUTPUT)

Rear output (REAR OUTPUT)

15 cm

Front output (FRONT OUTPUT)

Blue/white

To system control terminal of the power amp

or Auto-antenna relay control terminal (max.

15 cm

300 mA 12 V DC).

System remote control

Front speaker

≠

White

Gray

Front speaker

≠

White/black

Gray/black

Left

Green

Violet

Rear speaker

≠

Green/black

Violet/black

Rear speaker

≠

Subwoofer

≠

Perform these connections when using a

different amp (sold separately).

Connecting cords with RCA pin

plugs (sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Front speaker

≠

Front speaker

≠

Right

Rear speaker

≠

Rear speaker

≠

Subwoofer

≠

Fig. 2