Pioneer Super Tuner IIID+ DEH-P800PRS Kurulum Kılavuzu - Sayfa 4

Araç Alıcısı Pioneer Super Tuner IIID+ DEH-P800PRS için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer Super Tuner IIID+ DEH-P800PRS 8 sayfaları. Pioneer deh-p800prs: install guide

Sayfayı Yazdır

Installation

Note:

•

If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.

•

Before making a final installation of the unit, tem-

porarily connect the wiring to confirm that the

(Fig. 7)

connections are correct and the system works

properly.

60°

•

Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

•

Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

•

The cords must not cover up the area shown in the

tions of the vehicle.

figure below. This is necessary to allow the

•

Install the unit where it does not get in the dri-

amplifres to radiate freely. (Fig. 8)

ver's way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

•

The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

— for instance, near a heater outlet.

Do not close this area.

DIN Front/Rear-mount

This unit can be properly installed either from "Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 9)

Holder

After inserting the holder into the dashboard, then

Dashboard

select the appropriate tabs according to the thick-

ness of the dashboard material and bend them.

182

(Install as firmly possible using the top and bottom

tabs. To secure, bend the tabs 90 degrees.)

Rubber bush

Screw

Removing the Unit (Fig. 10) (Fig. 11)

To remove the frame, extend top and bottom of the frame outwards in order to unlock it. (When reattaching

the frame, point the side with a groove downwards and attach it.)

•

It becomes easy to remove the frame if the front panel is released.

Frame

Fig. 7

Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into

place. Keeping the keys pressed against the

Fig. 8

sides of the unit, pull the unit out.

Fig. 9

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 12)

To remove the frame, extend top and bottom of the frame outwards in order to unlock it. (When reattaching

the frame, point the side with a groove downwards and attach it.)

•

It becomes easy to remove the frame if the front panel is released.

Frame

Fig. 10

2. Fastening the unit to the factory radio mounting bracket.

(Fig. 13) (Fig. 14)

Select a position where the screw holes of the bracket and the screw holes of the head unit become aligned

(are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 mm × 8 mm) or flush

surface screws (5 mm × 9 mm), depending on the shape of the screw holes in the bracket.

Fig. 11

Factory radio mounting bracket

Switching the DSP setting mode

This product features two operation modes: the 3-way network mode (NW) and the standard mode (STD).

You can switch between modes as desired. Initially, the DSP setting is set to the standard mode (STD).

•

After switching, reset the microprocessor. (Refer to operation manual.)

• Use a thin standard tip screwdriver to switch the DSP switch on the side of this

product (Fig. 15).

Fixing the front panel

Fig. 12

If you do not operate the removing and attaching the front panel function, use the supplied fixing screw and

fix the front panel to this unit (Fig. 16).

Fig. 13

Screw

Dashboard or Console

Fig. 14

Fig. 15

Fig. 16

Fixing screw