Pioneer XC-P01DAB-K Kullanım Talimatları Kılavuzu - Sayfa 13
Araç Alıcısı Pioneer XC-P01DAB-K için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Pioneer XC-P01DAB-K 30 sayfaları. Cd receiver system/ampli-tuner cd
Ayrıca Pioneer XC-P01DAB-K için: Hızlı Başlangıç Kılavuzu (33 sayfalar)
Sayfayı Yazdır
General control
General control
To turn the power on
Press the SYSTEM button on the remote control to turn on
both of the stereo receiver and CD player.
To turn on the stereo receiver only:
Press the RECEIVER button on the remote control or the
/I STANDBY/ON button on the stereo receiver.
To turn on the CD player only:
Press the CD button on the remote control or the
/I STANDBY/ON button on the CD player.
After use:
To turn off the unit, press the SYSTEM/ RECEIVER/ CD
button on the remote control, or press the /I STANDBY/ON
button on the stereo receiver/CD player.
Setting the clock
In this example, the clock is set to the 24-hour (0:00) display.
1 Turn on the stereo receiver.
Refer to
above for details.
To turn the power on
2 Press the CONTROL RCV button on the remote control.
3 Press the CLOCK button on the remote control.
The current day and time are displayed.
The default setting (Sun 0:00) is displayed when the first time
you set the clock.
4 Press ENTER button.
5 Use / to set the day, then press ENTER.
6 Use / to select 24-hour or 12-hour display, then
press ENTER.
The time is displayed in the 24-hour
display format (0:00 - 23:59).
The time is displayed in the 12-hour
display format (AM 0:00 - PM 11:59).
7 Use / to set the hour, then press ENTER.
8 Use / to set the minute, then press ENTER to
confirm.
Note
• Press the CLOCK or RETURN button to exit the setting
mode without setting the clock.
To confirm the time display:
Press the CLOCK button. The current time and day are
displayed in the front panel display of the stereo receiver for
5 seconds.
Note
• The current time and day display is canceled if;
the volume is adjusted.
-
the SETUP, BASS +/–, TREBLE +/–, DIRECT, or SLEEP
-
button is pressed.
the stereo receiver is turned off.
-
the input source for the stereo receiver is changed.
-
To readjust the clock:
Perform "Setting the clock" from step 1.
Note
• If the AC power cord of the stereo receiver is
disconnected from the wall socket, the clock setting is
cleared. Set the clock.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents.
Refer to
on page 27 for details.
Factory reset, clearing all memory
2 Perform "Setting the clock" from step 1 onwards.
General functions
Display brightness control
Select the stereo receiver or CD player by pressing the
CONTROL RCV or CONTROL CD button on the remote
control.
Press DIMMER button to dim the display brightness. The
brightness can be controlled in four steps.
Volume control
Press the VOLUME +/– on the remote control to increase or
decrease volume, or turn the VOLUME knob on the stereo
receiver to the right to increase volume, and to the left to
decrease the volume.
CAUTION
• The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It
is advisable to avoid exposure to high volume levels. Do
not turn the volume on to full at switch on. Listen to music
at moderate levels. Excessive sound pressure from
earphones and headphones can cause hearing loss.
Note
• If you turn off and on the stereo receiver with the volume
set to 61 or higher, the volume starts at 60.
• When the DIRECT function is off, the volume can be set
from minimum to 60.
13
En