Pioneer XV-DV515 Kurulum

Alıcı Pioneer XV-DV515 için çevrimiçi göz atın veya pdf Kurulum indirin. Pioneer XV-DV515 2 sayfaları. Dvd/cd receiver
Ayrıca Pioneer XV-DV515 için: Kurulum (2 sayfalar)

Sayfayı Yazdır

Setting up your XV-DV515 DVD/CD Receiver

When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet.

Do not use these speakers with any other system or amplifier as this may result in damage or fire. Before setting up, please read Important notes and safety precautions below for more information.

Check that you have all the accessories, then put

the batteries in the remote control.

Wireless speaker

• Wireless speaker (1)

• Transmitter (1)

system:

• 2-pin RCA cord (1)

• AC adaptor (1)

Satellite speaker

• Center (1)

• Speaker cords (x6)

system:

• Front (x2)

• Non-slip pads

• Subwoofer (1)

(x24)

Batteries and

remote control

Power cord *

STANDBY/ON

FM/AM

L1/L2

DVD

TUNER

LINE

* In some countries or regions, the shape of the

DISPLAY

OPEN CLOSE

power plug may sometimes differ from that

shown in the explanatory drawings.

DVD MENU

RETURN

TUNE+

ST–

ST+

ENTER

MUTE

TUNE–

SOUND

MASTER

VOLUME

TV CONTROL

Video cord

INPUT

VOL

OPEN

AM loop antenna

FM antenna

Connect each speaker using the color-coded speaker cords.

Match them to the colored labels above the speaker terminals.

OUT

FRONT

CENTER

SURROUND

SPEAKERS

AUDIO

LINE 1

WIRELESS

SUB

WOOFER

Color-coded wire

(Connect to speaker)

Color-coded connector

(Connect to rear panel)

The supplied blue and grey speaker cords can be used to attach a

pair of speakers to the SURROUND speaker terminals. Make sure to

use speakers with a nominal impedence of 6Ω and a maximum input

power of no less than 75W.

Using the XW-DV515 digital wireless speaker system

The XW-DV515 wireless speaker system can be used for multi-channel sound with your main setup, or as a second stereo speaker system.

CHANNEL indicator

Lights to indicate the selected channel

CHANNEL button

Press to select a frequency channel. The frequency channel changes sequentially each time the button is

pressed:

CH 4

CH 1

CH 2

CH 3

Antenna

Transmits signals to the wireless speaker.

Wireless speaker antenna

Receives signals from the transmitter.

TUNED indicator

Lights when the signal from the transmitter is properly received.

AUTO indicator

Lights when AUTO is selected.

POWER button

Press to switch the speaker on or off.

WIRELESS MODE switch

Selects between SURROUND or STEREO.

SURROUND – Sounds going to the surround left and right channels are heard through the wireless speakers.

STEREO – Any source playing through the main system is heard in stereo through the wireless speakers (multi-

channel sources will be downmixed to stereo).

• Make sure you select the same mode on the main unit when doing this (see note below). Press the WIRELESS

button on the remote control and use the

and

W.Stereo (STEREO), or Off (this switches off all sound from the speaker) in the front panel display.

Press ENTER to confirm.

CHANNEL (AUTO ON/OFF) button

The default setting is AUTO, where the channel is automatically set to the same one selected on the transmitter.

If you find that the reception is weak, try switching to AUTO OFF. This 'locks' the signal and can result in better

reception.

Press and hold for about 5 seconds to switch between AUTO and AUTO OFF.

STEREO MODE VOLUME knob

Turn to adjust the speaker volume when WIRELESS MODE is set to STEREO.

• The STEREO MODE VOLUME knob has no effect when WIRELESS MODE is set to SURROUND.

Power cord

1 1

Connect to an AC outlet.

Caution

• Make sure to stop/turn off the source and switch off the wireless speaker when switching speaker

systems. The wireless speaker will output the source at very loud volumes if the wireless speaker is set to

SURROUND and the main unit is set to W.Stereo (STEREO). In this case, the volume control has no

effect, so please follow these precautions.

• Even when not in use, the fan in the wireless speaker will continue to operate. Switching off the wireless

speaker when not in use will increase product life.

• When you select SURROUND (on both units), you won't be able to hear anything through the speakers

connected to the surround left and right speaker terminals. The signals are sent to the wireless speakers

instead.

XRE3075A.En/Fr.01.02

All manuals and user guides at all-guides.com

Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.

Pull off the protective

shields of both AM antenna

wires.

Push open the tabs, then insert

one wire fully into each terminal.

Release the tabs to secure the AM

antenna wires.

Fix the AM loop antenna to the

attached stand.

To fix the stand to the antenna, bend in the

direction indicated by the arrow (fig. A) then

clip the loop onto the stand (fig. B).

Note: If you plan to mount the AM antenna

to a wall or other surface, secure the stand

with screws (fig. C) before clipping the loop

to the stand. Make sure the reception is clear.

Place the AM antenna on a flat

surface and point in the direction

giving the best reception.

Don't let it come into contact with metal

objects and avoid placing near computers,

television sets or other electrical appliances.

* Illustration shows the European model

OPTICAL IN

AUDIO

ANTENNA

LINE 2

AV CONNECTOR

UNBAL 75Ω

LOOP ANTENNA

AC IN

VIDEO

OUT

VIDEO

Subwoofer (Purple)

Front right

Center (Green)

(Red)

Remove the supplied non-slip pads from the paper, and stick four

onto the base of each satellite speaker.

Actual speakers supplied may differ from those shown.

Transmitter

wireless speaker

buttons to select W.Surr. (SURROUND),

Overhead view of a multi-channel (SURROUND) setup with the XW-DV515

For the best surround sound, setup your speakers as above.

The front left and right speakers should be about 1.8–2.7 m apart.

fig. A

fig. B

ANTENNA

UNBAL 75Ω

LOOP ANTENNA

European model

LOOP ANTENNA

UNBAL 75Ω

ANTENNA

All other models

Connect the FM wire antenna to the FM UNBAL 75Ω antenna terminal.

For best results, extend the FM antenna fully and fix to a wall or door

frame. Don't drape loosely or leave coiled up.

The signal earth (H) is designed to reduce noise that occurs when an

Note:

antenna is connected. It is not an electrical safety earth.

Connect each speaker as shown below.

Twist and pull off the protective

shields on each wire.

Connect the wires to the

speaker. Match the colored

wire with the color-coded

label (above the tabs), then

insert the colored wire into

the red (+) tab and the other

wire with the black (–) tab.

Connect the other end to the

color-coded speaker jacks on

the rear of the DVD/CD

receiver (as shown at left).

Make sure to insert completely.

Front left

(White)

These speaker terminals can be hazardous when live. When you connect or

disconnect the speaker cables, to prevent the risk of electric shock, do not

touch uninsulated parts before disconnecting the power cord.

CHANNEL

Digital

TUNED

AUTO

wireless

speaker system

STEREO MODE

POWER

WIRELESS

VOLUME

MODE

CHANNEL

OFF

SURROUND

STEREO

AUTO ON/OFF

MIN

MAX

STEREO MODE

POWER

WIRELESS

VOLUME

MODE

CHANNEL

OFF

SURROUND

STEREO

AUTO ON/OFF

MIN

MAX

Center

Subwoofer

Transmitter/

XV-DV515

CHANNEL

Front left

Front right

0 OPEN/CLOSE

STANDBY/ON

PHONES

wireless speaker

to AC outlet

03.3.11, 6:58 PM

Connect the WIRELESS (IN) jack on the transmitter to the

WIRELESS (OUT) jack on the rear panel of the DVD/CD

receiver using a 2-pin RCA cord, then connect to a power

outlet using the supplied AC adaptor.

fig. C

WIRELESS

Transmitter

* Illustration shows the European model

OPTICAL IN

OUT

AUDIO

LINE 2

AV CONNECTOR

AUDIO

LINE 1

WIRELESS

AC IN

VIDEO

OUT

VIDEO

XV-DV515 DVD/CD Receiver

When connecting, make sure both units are switched off and unplugged.

Connect the DVD/CD receiver to your TV, then connect the

supplied power cord.

Connect one end to a video input on your TV.

Use the supplied video cord.

Connect the other end to the video output of the DVD/CD receiver.

This player is equipped with copy protection technology. Do not connect this

player to your TV via a VCR using AV cables, as the picture from this player will not

appear properly on your TV.

Connect the power cord to the AC inlet.

VIDEO IN

* Illustration shows the European model

OUT

OPTICAL IN

AUDIO

LINE 2

AV CONNECTOR

AUDIO

LINE 1

WIRELESS

AC IN

VIDEO

OUT

VIDEO

AC IN

Congratulations! You're done setting up.

Printed in

Important notes and safety precautions

Using the remote control

The remote control can be used within a range of about 7 meters from the remote sensor on the front panel, and within a

30 degree angle.

Precautions:

• The remote control may not work if there is an obstacle between the remote control and the display unit, or if the remote

control is not directed towards the remote sensor of the display unit at the correct angle.

• The remote control may not work properly if strong light such as direct sunlight or fluorescent light is shining onto the

unit's remote sensor.

• The remote control may not work properly when this unit is used near devices emitting infrared rays, or when remote

controls of other devices which use infrared rays are used. Also, the use of this remote control may cause other devices to

work improperly.

• When the operating range of the remote becomes too short, replace the batteries.

Remote control battery caution

Incorrect use of batteries may cause leakage or rupture.

Always be sure to follow these guidelines:

• Always insert batteries into the battery compartment correctly matching the positive ª and negative · polarities, as

shown by the display inside the compartment.

• Never mix new and used batteries.

• Batteries of the same size may have different voltages, depending on brand. Do not mix different brands of batteries.

• When disposing of used batteries, please comply with governmental regulations or environmental public instruction's rules

that apply in your country or area.

• In order to prevent battery leakage, remove the batteries when not using the remote control for an extended period (one

month or more). If leakage occurs, carefully wipe away any battery fluid inside the compartment, and replace the batteries

with new ones.

• Do not allow books or other objects to rest on top of the remote control, since the buttons may be depressed, causing

faster exhaustion of the batteries.

Additional notes on connecting antennas

• Keep antenna cables away from other cables and the display unit and main set.

• To assure optimum reception, pull the FM antenna so that it is fully extended and not coiled or hanging at the rear of the unit.

• If reception with the supplied antenna is poor, see the Other Connections section in the main operating instructions for

details on connecting outdoor antennas.

Additional notes on speaker placement

Place speakers as shown in step 4 to achieve the optimum surround sound effect

• Install the main front left and right speakers at an equal distance from the TV.

1 1

• For optimum effect, install the rear speakers slightly above ear level.

• This system's speakers are magnetically shielded, so there's virtually no picture color distortion when they are placed near

a TV. In the rare event that there is some picture color interference, switch power to the TV off, and wait 15 to 30 minutes

before switching on again.

• Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

• When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means.

Otherwise, the speaker may fall from the TV due to external shocks such as earthquakes, endangering those nearby or

damaging the speaker.

• Do not connect the supplied speakers with any other amplifier. This may result in malfunction or fire.

Additional notes on wireless speaker placement

• Depending on your room characteristics, there will be places where you will achieve better reception from the transmitter.

If you are experiencing bad reception, try moving the speaker slightly. If the problem persists, try locating the best frequency

channel with the two units quite close together, then moving them further away once you have switched to AUTO OFF.

AC adaptor and power cord caution

• Do not leave the power cord near heating equipment. The coating of the cord may melt, which could lead to fire and/or

electrocution.

• Make sure to grasp the body of the AC adaptor when removing it from the power outlet. If you pull the power cord, it

may become damaged which could lead to fire and/or electrocution.

• Do not attempt to plug in or remove the AC adaptor with wet hands. This may result in electrocution.

• Insert the prongs of the AC adaptor all the way into the power outlet. If the connection is incomplete, heat may be

generated which could lead to fire. Furthermore, contact with the connected prongs of the adaptor may result in

electrocution.

• Do not insert the AC adaptor into a power outlet where the connection remains loose despite inserting the prongs all the

way into the outlet. Heat may be generated which could lead to fire. Consult with the retailer or an electrician regarding

replacement of the power outlet.

Placing the wireless speaker

For best surround sound, make sure to place the wireless speaker directly behind the center of the listening position and no

higher than ear level. Also, make sure you don't move the wireless speaker too far behind the listening position or you will lose

much of the surround sound effect.

For a greater surround sound effect from the wireless speaker, see Setting the channel levels on page 59 (XV-DV515) to

increase the surround channel levels.

adaptor

To power outlet

ANTENNA

UNBAL 75Ω

LOOP ANTENNA

ANTENNA

UNBAL 75Ω

LOOP ANTENNA

To AC outlet

<XRE3075-A>