Pioneer VSX-524-K Kullanım Talimatları Kılavuzu - Sayfa 34
Stereo Alıcı Pioneer VSX-524-K için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Pioneer VSX-524-K 40 sayfaları. Av receiver
Ayrıca Pioneer VSX-524-K için: Kullanım Talimatları Kılavuzu (38 sayfalar), Kullanım Talimatları Kılavuzu (40 sayfalar), Hızlı Başlangıç Kılavuzu (21 sayfalar), Hızlı Başlangıç Kılavuzu (21 sayfalar)
Sayfayı Yazdır
6
6
Adjust the level of each speaker as the test tone is
emitted.
Note
•
If you are using a Sound Pressure Level (SPL) meter, take
the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighting/slow
reading).
•
The subwoofer test tone is output at low volumes. You may
need to adjust the level after testing with an actual
soundtrack.
6
When you're finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
•
You can change the channel levels at any time by press
, then press
and
CH SELECT
RECEIVER
remote control. You can also press
CH SELECT
to select the channel, and then use
channel levels.
Speaker Distance
For good sound depth and separation from your system, you
need to specify the distance of your speakers from the
listening position. The receiver can then add the proper delay
needed for effective surround sound.
•
For the assignment of the digital signal inputs, see
Selecting the audio input signal on page
1
Select 'Manual SP Setup' from the Home Menu.
2
Select 'Speaker Distance' from the Manual SP Setup
menu.
2.Manual SP Setup
2d.Speaker Distance
a.Speaker Setting
Front L
Center
b.X.Over
c.Channel Level
Front R
d.Speaker Distance
Surround R
Surround L
Subwoofer
Return
3
Adjust the distance of each speaker using /.
You can adjust the distance of each speaker in 0.1 m
increments.
4
When you're finished, press RETURN.
You return to the Manual SP Setup menu.
The Input Assign menu
ANALOG IN1 audio input terminal is assigned to CD under
factory settings, but this can be changed to TV input.
1
Select 'Input Assign' from the Home Menu.
on the
LEV +/–
/
and use
/
to adjust the
2
Select 'Analog Input' from the Input Assign menu.
3.Input Assign
a.Analog Input
22.
3
Select the desired input option for the ANALOG IN1
audio input terminal.
4
When you're finished, press RETURN.
3 m
You return to the Input Assign menu.
[
3 m
]
[
3 m
]
[
3 m
]
[
3 m
]
[
3 m
]
Return
Home Menu
1. Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Auto Power Down
5.HDMI Setup
Re turn
3a.Analog Input
Analog
CD
Return
Return
34
The Auto Power Down menu
Set to automatically turn off the receiver after a specified time
has passed (when the power has been on with no operation
for several hours).
•
Default setting: OFF
1
Select 'Auto Power Down' from the Home Menu.
Home Menu
4.Auto Power Down
1 . Auto MCACC
Auto Power Down
2.Manual SP Setup
3.Input Assign
4.Auto Power Down
5.HDMI Setup
R et urn
2
Specify the amount of time to allow before the power
is turned off (when there has been no operation).
•
You can select 2, 4 or 6 hours, or OFF (if no automatic
shutoff is desired).
3
When you're finished, press RETURN.
You return to the Home Menu.
Important
•
If the Standby Through of the HDMI Setup is not set to
OFF, the Auto Power Down setting will automatically be
set to OFF and cannot be changed (VSX-524 only).
Home Menu
4
6
36
OFF
Return