Pioneer VSX-5300 Kullanım Talimatları Kılavuzu - Sayfa 34

Stereo Alıcı Pioneer VSX-5300 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Pioneer VSX-5300 37 sayfaları. Audio/video stereo receiver
Ayrıca Pioneer VSX-5300 için: Servis Kılavuzu (44 sayfalar)

Sayfayı Yazdır

TROUBLESHOOTING

Incorrect operation is often mistaken for equipment maifunction. If you think that there is something wrong with this component, check the points

below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used.

lf the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer

to carry out repair work.

[

Symptom

Cause

Remedy

Power does not come

on even when POWER

switch is pressed.

* Power cord is disconnected.

® Instances. are rare, but the problem may be due to

the operation of the protector circuit.

* Connect cord securely.

¢ Unplug the power cord of the unit from the AC wail

outlet, then plug it in again.

Control was not possible

regardless of what

operation switch was

pressed.

* Static electricity affected the unit when the air was

dry, such as in winter.

Unplug the power cord of the unit from the AC wall

outlet, then plug it in again.

If static electricity is pronounced, it is recommended

that you operate the unit using the remote controller.

No sound is produced,

even when the INPUT

SELECTOR switch is

selected.

* The MUTE switch is pressed.

e VOLUME

switch is turned down.

Consult page

—

11 and perform connections

correctly.

Press the MUTING switch to cance! the MUTING

effect.

Raise volume.

¢ Speaker connecting wires are disconnected from

speaker terminals.

Connect wires to terminals securely.

® One or both of the input cords are disconnected.

Connect input cords securely.

Press the switch again to the OFF position.

bee TAPE2/DAT2 MONITOR switch is in the ON position.

¢ Connector

bars are disconnected.

Connect bars securely.

® Stations memorized in the STATION CALL switches

are erased.

Consult your Pioneer authorized service station.

No picture is produced,

even when the INPUT

SELECTOR

switch is

selected.

* Connections

are incorrect.

¢ The VIDEO SIGNAL SELECTOR

is not set properly.

e The VCR and the selected INPUT SELECTOR

switch are not correct.

Consult page

—

11 and perform connections

correctly.

¢ Set correctly.

¢ Press the correct switch.

High noise level

* Station has not been tuned in to correct frequency.

e Antenna has not been connected or has become

disconnected.

* Tune the station in correctly.

* Connect the antenna securely.

FM reception

¢ Accessory T-type antenna remains bundled up or it

is not pointing in right direction.

® Stretch both ends of antenna taut and locate direction

yielding optimum reception.

« Weak broadcasting station signals.

Replace accessory T-type antenna with outdoor FM

antenna.

AM reception

¢ AM loop antenna is not pointing in right direction.

Change the direction of AM loop antenna and find

a position where reception is improved.

° Weak broadcasting station signals.

Erect outdoor AM antenna or connect ground wire.

* Noise being picked up from this unit and other

equipment (especially electrical appliances using

motor or fluorescent lights).

Stop using appliances generating noise or remove

them from vicinity of stereo equipment.

Separate the loop antenna from the unit by some

distance.

No auto stop

Input signals are not strong enough.

(FM) If the T-type antenna is being used, change to

an outdoor antenna.

TV source can't be

seen when the VCR's

TV tuner is used.

TV antenna is not connected to VCR, or connec-

tions are faulty.

Consult the VCR's operating instructions, and connect

antenna correctly.

¢ You are attempting to watch a TV source using a

VCR with copy system connections.

In general, when copy system connections are

mada, the VCR's TV tuner function ceases to

Operate.

For details, consult

the operating instruc-

tions for your VCR.

¢ Disconnect the copy system connection (TV tuner

function will operate).

Video tape copies

can't be made with

* Video tape copy connections haven't been made.

¢ Look again closely at the section VIDEO SYSTEM

CONNECTIONS

on page 7,11, and connect correctly.