Pioneer VSX-9500S VSX-7500S Kullanım Talimatları Kılavuzu - Sayfa 48
Stereo Alıcı Pioneer VSX-9500S VSX-7500S için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Pioneer VSX-9500S VSX-7500S 48 sayfaları.
Ayrıca Pioneer VSX-9500S VSX-7500S için: Kullanım Talimatları Kılavuzu (48 sayfalar)
Sayfayı Yazdır
TROUBLESHOOTING
TV source can't be seen when
* TV antenna
the VCR's TV tuner is used.
connections are faulty
instructions for your VCR.
[$3 lo eee
not connectod to VCR, or
* You are attempting to watch a TV source using
a VCR with copy system connections,
In general, when copy system connections are
made, the VCR's TV tuner function ceases to
operate. For details, consult the operating
© Consult the VCR's operating instructions, and
connect antenna correctly.
* Disconnect the copy system connection.
i Video tape copies can't be made
| with the VCR.
|
SPECIFICATIONS
* Video tape copy connections haven't been made.
* Look again closely at the section VIDEO
SYSTEM
CONNECTIONS
on page 9 and 36,
and connect correctly.
Amplifier section
[POWER
AMP
IN}
Continuous average power output of 125 watts*
per channel, min., at 8 ohms, from 20 Hz to 20,000
Hz with no more than 0.005 %** total harmonic
distortion (front); 30 watts* per channel, min., at
8 ohms, from 20 Hz to 20,000 Hz with no more
than 0.08 %**
total harmonic distortion {rear); 30
watts*, min., at 8 ohms, from 20 Hz to 20,000 Hz
with
no more
than
0.08
%**
total harmonic
distortion (center: VSX-9500S only).
Dynamic power (2 2/4 0/8).
seseeeeerees, 280 W/260 W/185 W
Audio section
Damping Factor
1 kHz, 82.
- 100
Input (Sensitivity/impedance)
PHONO
MM
-. 2.5 mV/47 kQ
CD, LINE, TAPE
1/DAT, TAPE 2, VIDEO, TV,
VDP/CDV,
VCR 1, VCR 2, VCR 3.0... eee
150 mV/47 kO
POWER AMP IN
1 V/47 kD
Phono Overload Level (T.H.D. 0.08 %, 1000 Hz)
PHONO
MM......00.¢.cereinesccnecrecssersessanceveraasesanesasecsaee
150 mV
Frequency Response
PHONO
MM...
20 Hz to 20,000 Hz +0.3 dB
CD, LINE, TAPE
1/DAT, TAPE 2, VIDEO, TV,
VDP/CDV,
VCR 1, VCR 2, VCR 3.
. 5 Hz to 100,000 Hz2$ dB
Output (Level/Impedance)
TAPE
1/DAT REC, TAPE 2 REC, VCR 1 OUT,
VCR 2 OUT...
150 mV/2.2 kQ
PRE AMP OUT
vee
1 V/220 9
Loudness Contour ..........ssesssrctrseetecssecceneseonenes +6 dB (100 Hz)
+3 dB (10 kHz)
Signal-to-Noise Ratio (IHF, short circuited, A network)
PHONO
MM
CD, LINE, TAPE
1/DAT, TAPE 2, VIDEO, TV,
VODP/CDV, VCR 1, VCR 2, VCR 3
Signal-to-Noise Ratio [EIA, at 1 W {1 kHz)}
PHONOEMM y fscccavacw canes cvrncicvns cotveencbiuacda vie cdeyeadeaeg nears 77 dB
CD, LINE, TAPE
7/DAT, TAPE 2, VIDEO, TV,
VDP/CDV,
VCR
1, VCR 2, VCR 3.
VIDEO Section
input (Sensitivity/impedance)
VCR 1, VCR 2, VCR 3, VDP/CDV, TV, VIDEO,
ADAPTOR.........
Shecavsblgneetuns
Ta epeccesegileltaay « 1 Vp-p/75 0
Output
(Level/impedance)
VCR 1, VCR 2, ADAPTOR,
MONITOR
................. 1 Vp-p/75 Q
Frequency Responce
VCR 1, VCR 2, VCR 3, VDP/CDV, TV, VIDEO,
ADAPTOR
MONITOR
......c:csccseececeeeeee 5 Hz - 10 MHz*$ dB
Signai-to-Noise Ratio
55 dB
Cross Talk .
. 55 dB (3.58 MHz)
Enhancer ..
+3 dB (2 MHz)
{S terminals]
input (Sensitivityfimpedance}
VCR 1, VCR 2, VDP/CDV
vo.
Luminance signal: 1 Vp-p/75 Q
Color difference signal; 0.286 Vp-p/75 Q
Output (Levei/impedance)
VCR
7, VCR 2, TO MONITOR TY. Luminance signal: 1 Vp-p/75 2
Color difference signal; 0.286 Vp-p/75 Q
Frequency response
Luminance Signal ...........:cceccereee
eee eeeee 10 Hz to 10 MHz, 73 4B
Signal-to-Noise Ratio
Luminance signal
Cross talk
55 dB
. §5 dB (3.58 MHz)
Surround section
Input {Sensitivityimpedance)
REAR POWER AMP IN...
1 Vi47 kQ
CENTER POWER ANP IN
- 1 V/47 ko
Output {Level/impedance}
REAR PRE AMP OUT
0.0... ccc ce eceseeeseeeeeereenteser eee 1 V/470 0
CENTER PRE AMP OUT
VSX-9500S
.
«
1 V/4702
VSX-7500S
.
. 2 V/4700
47
<ARBI173>