Pioneer VSX-D510 Kullanım Talimatları Kılavuzu - Sayfa 38
Stereo Alıcı Pioneer VSX-D510 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Pioneer VSX-D510 40 sayfaları. Audio/video multi-channel receiver
Ayrıca Pioneer VSX-D510 için: Kullanım Talimatları Kılavuzu (36 sayfalar), Servis Kılavuzu (14 sayfalar)
Sayfayı Yazdır
Additional Information
10
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
The power does not turn ON.
• Connect the power plug to the wall outlet.
• Disconnect the power plug from the outlet, and
insert again.
• Make sure there are no loose strands of speaker wire
touching the rear panel. This could cause the receiver
to shut off automatically.
The unit does not respond when the buttons are
pressed.
No sound is output when a function is selected.
• Make sure the component is connected correctly
(refer to pages 5 to 10).
• If MUTING is on, press
control to turn it off.
• Adjust
MASTER VOLUME
• If MONITOR is on, press the MONITOR button to
turn it off.
• If no speakers are selected, press
select the speakers you connected.
No image is output when a function is selected.
• Make sure the component is connected correctly
(refer to pages 5 to 10).
• Press the correct function button.
Considerable noise in radio broadcasts.
• Tune in the correct frequency.
• Connect the antenna (refer to page 8).
• Route 2 RF and digital cables away from the
antenna terminals and wires.
• Fully extend the FM wire antenna, position for best
reception, and secure to a wall.
• Connect an outdoor FM antenna (refer to page 8).
• Adjust the direction and position for best reception.
• Connect an additional internal or external AM
antenna (refer to page 8).
• Turn off the equipment causing the noise or move it
away from the receiver.
• Place the antenna farther away from the equipment
causing the noise.
Broadcast stations cannot be selected automatically.
• Connect an outdoor antenna (refer to page 8).
38
En
on the remote
MUTING
.
to
SPEAKERS
No sound from surround or center speakers.
• Refer to "SPEAKERS setting mode" on pages 11-14 to
check the speaker settings.
• Refer to "Setting the Volume Level of Each Channel"
on page 15 to check the speaker levels.
• Connect the speakers (refer to page 9).
Sound is produced from other components, but not
from LD or DVD player.
• Set SIGNAL SELECT to "DIGITAL" or "ANALOG"
according to the type of connections made. (refer to
page 21).
• Set the digital input settings correctly (refer to pages
14 to 15).
• Make digital connections (refer to page 6) and set
SIGNAL SELECT to "DIGITAL" (refer to page 21).
• Refer to the instruction manual supplied with the
DVD player.
No sound is output or a noise is output when
software with DTS is played back.
• Set the digital volume level of the player to full, or to
the neutral position.
When a search is performed by a DTS compatible
CD player during playback, noise is output.
• This is not a malfunction, but be sure to turn the
volume down to prevent the output of loud noise
from your speakers.
Cannot be remote controlled.
• Replace the batteries (refer to page 4).
• Operate within 7 m, 30° of the remote sensor on the
front panel (refer to page 4).
• Remove the obstacle or operate from another
position.
• Avoid exposing the remote sensor on the front panel
to direct light.
The display is dark or off.
• Press
on the remote control repeatedly
FL DIMMER
to return to the default.
If the unit does not operate normally due to external
effects such as static electricity disconnect the power
plug from the outlet and insert again to return to normal
operating conditions.