Pioneer GM-X404 Servis Kılavuzu - Sayfa 16

Amplifikatör Pioneer GM-X404 için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Pioneer GM-X404 17 sayfaları. Bridgeable four-channel power amplifier
Ayrıca Pioneer GM-X404 için: Servis Kılavuzu (18 sayfalar), Kullanıcı El Kitabı (22 sayfalar)

Sayfayı Yazdır

GM-xX404,x304

Connecting the Unit

A\ CAUTION

Remove the negative (-) terminal of the

battery to avoid the risk of short-circuit

and damage to the unit.

Secure the wiring with cable clamps or

adhesive tape. To protect the wiring,

wrap adhesive tape around them where

they lie against metal parts.

Do not route wires where they will get

hot, for example where the heater will

blow over them. If the insulation heats

up, it may become damaged, resulting in

8 short-circuit through the vehicle body.

Make sure that wires will not interfere

with moving parts of the vehicle, such as

the gearshift, handbrake or seat sliding

mechanism.

Do not shorten any wires. Otherwise the

protection circuit may fail to work when it

should.

Never feed power to other equipment by

cutting the insulation of the power supply

wire to tap from the wire. The current

capacity of the wire will be exceeded,

causing overheating.

Be sure to use the special red battery wire

supplied with the amplifier and connect

directly to the battery. Use the supplied

black ground wire and connect to the

vehicle body. (The supplied special red

battery and ground wires are designed so

that the amplifier can be connected

safely.)

{18} Blue

Connect the male terminal of this wire

to the blue wire of the car stereo

(system control terminal). The female

terminal can be connected to the auto-

antenna relay control terminal.

lf the car stereo does not have a

system remote control terminal,

connect the male terminal to the power

terminal through the ignition switch.

[19] Speaker output terminals

See the "Connecting the Speakers and

Input wires" section for speaker con-

nection instructions.

@ To prevent damage

Do not ground the speaker lead wire

directly or connect a negative (—) lead

wire for several speakers.

Speakers to be connected to the amplifier

should conform with the standards listed

below. Otherwise damage will be caused

to the speaker. The speaker impedance

must be 2 to 8 ohms.

This unit is for vehicles with a 12-volt

battery and negative grounding. Before

installing it in a recreational vehicle, truck,

or bus, check the battery voltage.

* Install and route the sold separately

special red battery wire supplied with the

amplifier as faraway as possible from the

speaker wires. Install and route the

battery wire, ground wire, speaker wires,

and the amplifier as faraway as possible

| Channei

| Type

Four-

channel

Other than

sub-woofer

Two-

channel

Other than

sub-woofer

Three-

channel

Speaker

output A

Nominal input:

Min. 30 W

Max. input:

Min. 60 W

Nominal input:

Min. 70W

Max. input:

Min. 140 W

Three-

channel

Speaker

output B

Connecting the Power Terminal

Be sure to use the special red battery wire

supplied with the amplifier and connect

directly to the battery. Use the supplied

black ground wire and connect to the

vehicle body. (The supplied special red

battery and ground wires are designed so

that the amplifier can be connected

safely.)

Pass the special red battery wire from the

engine compartment to the interior of the

vehicle.

Fuse

(30 A)

Engine

Interior of

compart-

the vehicle

ment

Special red

battery wire

After making all

other connections

at the amplifier,

connect the battery

wire terminal of the

Drill an 8-mm

hole into the

vehicle body.

insert the

O-ring rubber

grommet into

the vehicle body.

amplifier to the

positive (+) terminal

of the battery.

Fig. 22

Nominal input:

Other than

Max. input:

sub-woofer | Min. 60 W

Nominal input:

Other than

Max. input:

sub-woofer | Min. 140 W

from the antenna, antenna cable and

tuner.

(Fig. 20)

{8] Special red battery wire

After making all other connections

at the amplifier, connect the battery

lead terminal of the amplifier to the

positive (+) terminal of the battery.

Ground wire (black)

Connect to metal body or chassis.

[10] Fuse (Special red battery power wire:

30 A, Amplifier: 25 A)

{11] Grommet

[12] Car stereo with RCA output pin jacks

[13] External Output

For details on how to connect to RCA

input jacks A and B, see the

"Connecting the Speakers and Input

wires" section.

If only one input pin plug, do not

connect anything to RCA input jack B.

[14] White

[15] Red

(16] Connecting wires with RCA pin plugs

(sold separately)

[17] RCA input pin jack A, B

[9]

Connect the special red battery wire to thr

POWER terminal (+), and the black ground

wire to the GND terminal (-).

POWER

Terminal

terminal

screw

Terminal

GND

screw

terminal

Ground wire

(black)

Special red

battery wire

Fig. 23

Fig. 24

+ Securely fasten the special red battery

lead and the ground wires with terminal

screws.

Connecting the Speakers and Input

wires

The speaker output mode can be four-

channel, three-channel (stereo + mono) or

two-channel (stereo, mono). Connect the

speakers according to figures on following

pages.