Pioneer gm-x972 Kullanıcı El Kitabı - Sayfa 3
Amplifikatör Pioneer gm-x972 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Pioneer gm-x972 9 sayfaları. Bridgeable power amplifier
Ayrıca Pioneer gm-x972 için: Servis Kılavuzu (25 sayfalar)
Connecting the Unit
Connecting the Power Terminal
4. Connect the wires to the terminal.
• Fix the wires securely with the terminal
• Always use the special red battery and ground
screws.
wire [RD-223], which is sold separately. Connect
GND terminal
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
System remote
control terminal
1. Pass the battery wire from the
System remote
engine compartment to the interior
control wire
of the vehicle.
• After making all other connections to the
amplifier, connect the battery wire terminal of
Ground wire
the amplifier to the positive (+) terminal of
the battery.
Engine
Fuse (30 A)
compart-
Interior of
the vehicle
ment
Battery wire
Fuse (30 A)
Connecting the Speaker Output
Drill a 14 mm
Positive terminal
hole into the
Terminals
vehicle body.
Insert the O-ring rubber
grommet into the vehicle
body.
1. Expose the end of the speaker wires
using nippers or a cutter by about
10 mm and twist.
2. Twist the battery wire, ground wire
and system remote control wire.
Twist
10 mm
2. Attach lugs to speaker wire ends.
Lugs not supplied.
3. Attach lugs to wire ends. Lugs not
• Use pliers, etc., to crimp lugs to wires.
supplied.
Lug
• Use pliers, etc., to crimp lugs to wires.
Lug
Speaker wire
Ground wire
Lug
Battery wire
3. Connect the speaker wires to the
Using the Speaker Input
speaker output terminals.
• Connect the speaker wires, passing them
through the terminal cover.
• Fix the speaker wires securely with the termi-
Power terminal
nal screws.
Terminal screw
7 Connections when using the speaker
input
Terminal cover
Speaker
output
terminal
Speaker wire
4. Push on the terminal cover.
Twist
Connecting the Speaker wires
Connect the car stereo speaker output
The speaker output mode can be two-channel (stereo) or one-channel
wires to the amplifier using the supplied
(mono). Connect the speaker leads to suit the mode according to the figures
speaker input connector.
shown below.
• Do not connect both the RCA input and the
• Do not connect both the RCA input and the speaker input at the same time.
speaker input at the same time.
Two-channel mode (stereo)
Car Stereo
Speaker output
One-channel mode (mono)
White/black:
Gray/black:
Left ≠
Right ≠
White:
Gray:
Left +
Right +
Speaker input connector
To speaker input terminal of
this unit.
Installation
CAUTION
• Do not install in:
—Places where it could injure the driver or pas-
sengers if the vehicle stops suddenly.
—Places where it may interfere with the driver,
such as on the floor in front of the driver's
seat.
• Make sure that wires are not caught in the sliding
mechanism of the seats, resulting in a short-cir-
cuit.
• Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier.
Protect all cables and important equipment such
as fuel lines, brake lines and electrical wiring
from damage.
• Install tapping screws in such a way that the screw
tip does not touch any wire. This is important to
prevent wires from being cut by vibration of the
(Right)
car, which can result in fire.
Speaker
• To prevent electric shock, do not install the ampli-
(Left)
fier in places where it might come in contact with
liquids.
• To ensure proper installation, use the supplied
parts in the manner specified. If any parts other
than the supplied ones are used, they may damage
internal parts of the amplifier, or they may
become loose causing the amplifier to shut down.
To prevent malfunction
• To ensure proper heat dissipation of the amplifier,
be sure of the following during installation.
—Allow adequate space above the amplifier for
proper ventilation.
—Do not cover the amplifier with a floor mat or
carpet.
• Do not install the amplifier near a door where it
may get wet.
• Do not install the amplifier on unstable places
such as the spare tire board.
Speaker (Mono)
• The best location for installation differs with the
car model and installation location. Secure the
amplifier at a sufficiently rigid location.
• Make temporary connections first and check that
the amplifier and the system operate properly.
• After installing the amplifier, confirm that the
spare tire, jack and tools can be easily removed.
Example of installation on the floor
mat or on the chassis
1. Place the amplifier where it is to be
installed. Insert the supplied tapping
screws (4 × 18 mm) into the screw
holes. Push on the screws with a
screwdriver so they make marks
where the installation holes are to be
located.
2. Drill 2.5 mm diameter holes at the
point marked, and install the ampli-
fier, either on the carpet or directly
to the chassis.
Tapping-screws
(4 × 18 mm)
Floor mat
or chassis
Drill a 2.5 mm diameter hole