Pioneer PRS-D1000M Kullanıcı El Kitabı - Sayfa 2

Amplifikatör Pioneer PRS-D1000M için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Pioneer PRS-D1000M 9 sayfaları. Class d mono amplifier
Ayrıca Pioneer PRS-D1000M için: Kullanıcı El Kitabı (50 sayfalar), Kullanıcı El Kitabı (9 sayfalar), Servis Kılavuzu (38 sayfalar)

Sayfayı Yazdır

Connecting the Unit

CAUTION

• Disconnect the negative (–) terminal of the battery

• Make sure that wires will not interfere with mov-

to avoid the risk of short-circuit and damage to

ing parts of the vehicle, such as the gearshift,

the unit.

handbrake or seat sliding mechanism.

• Secure the wiring with cable clamps or adhesive

• Do not shorten any wires. Otherwise the protec-

tape. To protect the wiring, wrap adhesive tape

tion circuit may fail to work when it should.

around it where they lie against metal parts.

• Never feed power to other equipment by cutting

• Do not route wires where they will get hot, for

the insulation of the power supply wire to tap

example where the heater will blow over them. If

from the wire. The current capacity of the wire

the insulation heats up, it may become damaged,

will be exceeded, causing overheating.

resulting in a short-circuit through the vehicle

• Never replace the fuse with one of greater value

body.

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent damage and/or injury

• Do not ground the speaker wire directly or con-

• Connect either of three subwoofers to the amplifi-

nect a negative (–) lead wire for several speakers.

er; 1: a subwoofer with a 420 W or larger nominal

input and an impedance 4 Ω, 2: a subwoofer with

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

a 600 W or larger nominal input and an imped-

ance 2 Ω or 3: a subwoofer with a 600 W or larg-

ational vehicle, truck or bus, check the battery

er nominal input and an impedance 1 Ω. If the

voltage.

• If the car stereo is kept on for a long time while

nominal input and impedance are out of the above

the engine is at rest or idling, the battery may go

ranges, the subwoofer may catch fire, emit smoke

dead. Turn the car stereo off when the engine is at

or become damaged.

rest or idling.

• Install and route the separately sold battery wire

• If the system remote control wire of the amplifier

as far away as possible from the speaker wires.

is connected to the power terminal through the

Install and route the separately sold battery wire,

ignition switch (12 V DC), the amplifier will

ground wire, speaker wires and the amplifier as

always be on when the ignition is on— regardless

far away as possible from the antenna, antenna

of whether the car stereo is on or off. Because of

cable and tuner.

this, the battery could go dead if the engine is at

• Cords for this product and those for other prod-

rest or idling.

ucts may be different colors even if they have the

• DO NOT connect a subwoofer with a lower

same function. When connecting this product to

impedance than specified in the "Connecting the

another product, refer to the supplied Installation

Unit" section. Amplifier damage, smoke, and

manuals of both products and connect cords that

overheating could result from a non-specified con-

have the same function.

nection. The amplifier surface could also become

hot to the touch and minor burns could result.

Connection Diagram

• This diagram shows connections using external output. Slide the input switch to the left.

• In the case of connecting the external output from a car stereo to an RCA input, use the jack used for full-

range output. This is because the LPF of the amplifier cannot be turned OFF. If this jack cannot be used,

connect the subwoofer output jack to the RCA input.

• When you connect with speaker output, connections defers from the diagram. For details, see the "Using

the Speaker Input" section. In either case, you need to set the input switch. For details, see the "Setting the

Unit" section.

• Always use the special red battery and ground wire ([RD-223] and [RD-222]), which are sold separately.

Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car

body. There is the risk of a fuse burning out if only one of these is connected.

Special red battery wire

Grommet

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to

the positive (+) terminal of the battery.

Fuse (30 A) × 3

Ground wire (black)

Connect to metal body or chassis.

[RD-223]

External Output

(sold separately)

[RD-222] (sold separately)

Bass Boost

Car stereo with

Remote Control

Bass Boost Remote

RCA output jacks

Control Wire

6 m

Jack for the bass boost

remote control

Connecting wire with RCA

Connect this jack and

pin plugs (sold separately).

the bass boost remote

control with the bass

boost remote control

wire.

RCA input jack

SYNC OUTPUT/SYNC INPUT jack

Speaker output terminal

Fuse (40 A)

See the "Connecting the Speaker Wires"

See the "Connecting the

section for SYNC OUTPUT/SYNC

Speaker Wires" section for

INPUT jack connection instructions.

speaker connection instruc-

tions.

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control terminal of the car

stereo (SYSTEM REMOTE CONTROL). The female terminal can be connected to the

auto-antenna relay control terminal. If the car stereo does not have a system remote control

terminal, connect the male terminal to the power terminal through the ignition switch.

Connecting the Power Terminal

3. Attach lugs to wire ends. Lugs not

supplied.

• Always use the special red battery and ground

• Use pliers, etc., to crimp lugs to wires.

wire ([RD-223] and [RD-222]), which are sold

separately. Connect the battery wire directly to the

Lug

car battery positive terminal (+) and the ground

wire to the car body. There is the risk of a fuse

burning out if only one of these is connected.

Ground wire

1. Pass the battery wire from the

Lug

engine compartment to the interior

of the vehicle.

Battery wire

• After making all other connections to the

amplifier, connect the battery wire terminal of

the amplifier to the positive (+) terminal of

the battery.

4. Connect the wires to the terminal.

[RD-223]

Engine

• Fix the wires securely with the terminal

Fuse (30 A)

compart-

Interior of

screws.

ment

the vehicle

GND terminal

Power terminal

System remote

control terminal

Fuse (30 A)

Drill a 14 mm

Positive terminal

hole into the

System remote

Insert the O-ring rubber

vehicle body.

control wire

grommet into the vehicle

Ground wire

body.

[RD-222]

Engine

compart-

Interior of

Fuse (30 A)

Battery wire

ment

the vehicle

Positive terminal

WARNING

Drill an 8 mm

Failure to securely fasten the battery wire to the ter-

Insert the O-ring rubber

hole into the

minal using the terminal screws could cause the ter-

grommet into the vehicle

vehicle body.

minal area to overheat and could result in damage

body.

and injury including minor burns.

2. Twist the battery wire, ground wire

and system remote control wire.

Twist

Connecting the Speaker Output

Using the Speaker Input

Terminals

Connect the car stereo speaker output

wires to the amplifier using the supplied

speaker input wire with RCA pin cord.

1. Expose the end of the speaker wires

• Slide the input switch to the right.

using nippers or a cutter by about

7 Connections when using the speaker

10 mm and twist.

input

Twist

10 mm

Car Stereo

2. Attach lugs to speaker wire ends.

Lugs not supplied.

Speaker

• Use pliers, etc., to crimp lugs to wires.

output

Lug

Speaker wire

White:

Black:

Red:

Left + Left ≠

Right ≠ Right +

3. Connect the speaker wires to the

speaker output terminals.

• Fix the speaker wires securely with the termi-

nal screws.

Terminal screw

Speaker input

wire with RCA

pin cord

To RCA

input jack of

this unit.

Speaker

output

terminal

• As a result of connecting the car stereo speaker

output wire to the amplifier, the power of the

amplifier is turned on automatically when the car

Speaker wire

stereo is turned on. It is not necessary to connect

the system remote control wire in this case.

• In the case the amplifier and head unit are con-

nected using a speaker input wire with RCA pin

cord, the amplifier power is only turned on when

one amplifier is being used. If two or more ampli-

fiers are synchronously connected in combination,

connect the head unit and all of the amplifiers

with the system remote control wire.

Note:

• Connect the system remote control wire when the

power of the amplifier is not to be turned on when

the car stereo is turned on.