Pioneer Premier DEH-P330 Kurulum Kılavuzu

CD Çalar Pioneer Premier DEH-P330 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer Premier DEH-P330 6 sayfaları. Pioneer deh-p330: install guide
Ayrıca Pioneer Premier DEH-P330 için: Kurulum Kılavuzu (6 sayfalar)

Sayfayı Yazdır

DEH-P3300

DEH-P33

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Los colores de los cables este producto se conforman

con el código de colores CEMA.

Printed in

Thailand

Imprimé

en Thaïlande

<CRD3314-A/JS> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

• When an external power amp is being used with

negative grounding. Before installing it in a recre-

this system, be sure not to connect the blue/white

ational vehicle, truck or bus, check the battery

lead to the amp's power terminal. Likewise, do not

voltage.

connect the blue/white lead to the power terminal

• To avoid shorts in the electrical system, be sure to

of the auto-antenna. Such connection could cause

disconnect the ≠ battery cable before beginning

excessive current drain and malfunction.

installation.

• To avoid short-circuiting, cover the disconnected

• Refer to the owner's manual for details on con-

lead with insulating tape. Especially, insulate the

necting the power amp and other units, then make

unused speaker leads without fail. There is a possi-

connections correctly.

bility of short-circuiting if the leads are not insulat-

• Secure the wiring with cable clamps or adhesive

ed.

tape. To protect the wiring, wrap adhesive tape

• To prevent incorrect connection, the input side of

around them where they lie against metal parts.

the IP-BUS connector is blue, and the output side

• Route and secure all wiring so it cannot touch any

is black. Connect the connectors of the same colors

moving parts, such as the gear shift, handbrake and

correctly.

seat rails. Do not route wiring in places that get

• If this unit is installed in a vehicle that does not

hot, such as near the heater outlet. If the insulation

have an ACC (accessory) position on the ignition

of the wiring melts or gets torn, there is a danger of

switch, the red lead of the unit should be connected

the wiring short-circuiting to the vehicle body.

to a terminal coupled with ignition switch ON/OFF

• Don't pass the yellow lead through a hole into the

operations. If this is not done, the vehicle battery

engine compartment to connect to the battery. This

may be drained when you are away from the vehi-

will damage the lead insulation and cause a very

cle for several hours. (Fig. 1)

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit.

ACC position

No ACC position

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

impedance of 4 to 8 ohms. Connecting speakers

ucts such as power amps.

with output and/or impedance values other than

If you ground the products together and the ground

those noted here may result in the speakers catch-

ing fire, emitting smoke, or becoming damaged.

becomes detached, there is a risk of damage to the

• When this product's source is switched ON, a con-

products or fire.

trol signal is output through the blue/white lead.

• Cords for this product and those for other prod-

Connect to an external power amp's system remote

ucts may be different colors even if they have the

control or the car's Auto-antenna relay control ter-

same function. When connecting this product to

minal (max. 300 mA 12 V DC). If the car features

another product, refer to the supplied Installation

a glass antenna, connect to the antenna booster

manuals of both products and connect cords that

power supply terminal.

have the same function.

This Product

Rear or Subwoofer output

Antenna jack

Multi-CD player

IP-BUS input (Blue)

(sold separately)

IP-BUS cable

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Red

Fig. 1

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

With a 2 speaker system, do not connect

To vehicle (metal) body.

anything to the speaker leads that are not

connected to speakers.

Perform these connections when using a

different amp (sold separately).

Connecting cords with RCA pin plugs

(sold separately)

Blue/white

Fuse

To system control terminal of the power amp or

Auto-antenna relay control terminal (max. 300mA

12 V DC).

System remote control

White

Gray

Front speaker

White/black

Gray/black

Left

Violet

Green

Rear Speaker

or Subwoofer

Green/black

Violet/black

Rear Speaker

or Subwoofer

Note:

When a subwoofer is connected to this unit instead of a rear speaker,

change the rear output setting in the Initial Setting. (Refer to the

Operation Manual.) The subwoofer output of this unit is monaural.

Power amp

(sold separately)

Front speaker

Right

Rear Speaker

or Subwoofer

Rear Speaker

or Subwoofer

Fig. 2