Ariston RPD 106 7 Kullanım Kılavuzu - Sayfa 8

Yıkayıcı Ariston RPD 106 7 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Ariston RPD 106 7 12 sayfaları.

Sayfayı Yazdır

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the On/Off

button

; the text HOTPOINT will appear on the display

and the START/PAUSE indicator light will flash slowly in

a green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

3. MEASURE OUT THE DETERGENT. Open the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in "Detergents

and laundry".

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle; the

name of the wash cycle will appear on the display. A

temperature and spin speed is set for each wash cycle;

these may be adjusted. The duration of the cycle will

appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin speed.

The machine automatically selects the maximum

temperature and spin speed set for the selected wash

cycle; these values cannot therefore be increased.

The temperature can be decreased by pressing the

button, until the cold wash (the display will visualise the

"--" symbol) setting is reached. The spin speed may be

progressively reduced by pressing the

it is completely excluded (the display will visualise the

"--" symbol). If these buttons are pressed again, the

maximum values are restored.

! Exception: if the 3 programme is selected, the

temperature can be increased up to a value of 90°C.

! Exception: if the 4 programme is selected, the

temperature can be increased up to a value of 60°C..

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. To remove the

delayed start function press the button until the text

"-- h" appears on the display.

Set the desired wash intensity.

Option

makes it possible to optimise washing based

on the level of soil in the fabrics and on desired wash

cycle intensity.

For heavily-soiled garments press button

"Intensive Wash" level is reached. This level ensures

a high-performance wash due to a larger quantity of

water used in the initial phase of the cycle and due to

increased drum rotation. It is useful when removing the

most stubborn stains.

For lightly-soiled garments or a more delicate treatment

of the fabrics, press button

wash" level is reached.

The cycle will reduce the drum rotation to ensure

washing results are perfect for delicate garments.

button, until

until the

until the "Delicate

Set the rinse type.

Option

makes it possible to select the desired

rinse type for sensitive skin. Press the button once for

the "Extra +1" level, which makes it possible to select

an additional rinse after the standard cycle rinse and

remove all traces of detergent. Press the button again

for the "Extra +2" level, which makes it possible to

select two additional rinses to the standard cycle rinses;

it is recommended for very sensitive skin. When the

button is pressed for the third time, the "Extra +3" level

is set, thus allowing the selection of 3 rinses in addition

to the standard cycle's rinses. The option - started with

cycles at a temperature of 40°C - makes it possible to

remove major allergens such as pollen, cat and dog

hair. With cycles at a temperature higher than 40° a very

good level of antiallergic protection is achieved. Press

the button again to go back to the "Normal rinse" rinse

type. If the current adjustment can be neither set nor

changed, the display will show "No Selection" or "No

Change".

Modifying the cycle settings.

• Press the button to enable the function; the relevant

indicator light on the display will light up.

• Press the button again to disable the function; the

relevant indicator light on the display will switch off.

! If the selected function is incompatible with the set

programme, the relevant indicator light will appear dimly

lit; in addition, the incompatibility will be signalled by a

buzzer (3 beeps) and the wording "No Selection" will

appear on the display.

! If the selected function is incompatible with another

previously set function, the wording "No Selection"

will appear on the display and the function will not be

enabled.

! The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol

be on). During the wash cycle, the name of the phase in

progress will appear on the display. To change a wash

cycle while it is in progress, pause the washing machine

using the START/PAUSE button (the START/PAUSE

indicator light will flash slowly in an orange colour);

then select the desired cycle and press the START/

PAUSE button again. To open the door while a cycle

is in progress, press the START/PAUSE button; if the

DOOR LOCKED

symbol is switched off the door

may be opened. Press the START/PAUSE button again

to restart the wash cycle from the point at which it was

interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text "CYCLE END" on the display;

when the DOOR LOCKED

the door may be opened. Open the door, unload the

laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the

button. The cycle will be stopped

and the machine will switch off.

will

symbol switches off