Pioneer VSX-S300-S Hızlı Başlangıç Kılavuzu - Sayfa 4

Hoparlör Sistemi Pioneer VSX-S300-S için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Pioneer VSX-S300-S 33 sayfaları. Audio/video multi-channel receiver

Sayfayı Yazdır

Pioneer VSX-S300-S Hızlı Başlangıç Kılavuzu

Basic setup

Canceling the Auto Power Down

When this receiver is not used over a period of several hours, it will power down

automatically. The automatic power-off timer is set to six hours under factory settings,

and the timing can be changed or the power-off function switched off altogether. 

"The Auto Power Down menu"

Automatically setting up for surround sound (MCACC)

The Auto Multi-Channel Acoustic Calibration (MCACC)

setup measures the acoustic characteristics of your

listening area, taking into account ambient noise,

speaker size and distance, and tests for both channel

delay and channel level. After you have set up the

microphone provided with your system, the receiver

uses the information from a series of test tones to

optimize the speaker settings and equalization for your

particular room.

CAUTION

• The test tones used in the Auto MCACC setup are

output at high volume.

Important

• The OSD will not appear if you have connected

using the HDMI output to your TV. Use composite

connections for Auto MCACC setup.

STANDBY/ON

ECO

D AUX

A AUX

S.RTRV

AUTO /

iPod USB NETWORK

ADAPTER

DIRECT

ALC /

TUNER

DVD

STANDARD

iPod

CTRL

ADV

STB

GAME

SURR

SOUND

RECEIVER

PORTABLE

WING

Note

• The subwoofer distance setting may be farther

than the actual distance from the listening

position. If this is the case, perform settings

manually. 

"Speaker Distance"

Change the X.OVER setting

For S-HV600B/S-HV500-LR/S-SL100-LR/S-SL100CR

speakers

Select 'Manual SP Setup' from the

Home Menu, then press ENTER.

Select 'X.OVER' from the Manual SP Setup

menu, then press ENTER.

2.Manual SP Setup

a.Speaker System

b.Speaker Setting

c.X.OVER

d.Channel Level

e.Speaker Distance

Choose '200 Hz' for the frequency cutoff

point.

2c.X.OVER

Frequency

200Hz

When you're ﬁ nished, press RETURN twice.

You return to the Home Menu.

Microphone

Tripod

Switch on the receiver and your TV.

AUDIO

DISP

SLEEP

SP-AB

DIMMER

STATUS

Switch the TV input to the input that connects this receiver to the TV through the corresponding

composite cable.

TOP

VOL

TOOLS

Connect the microphone to the MCACC SETUP MIC jack on the front panel.

Make sure there are no obstacles between the speakers and the microphone.

ENTER

If you have a tripod, use it to place the microphone so that it's about ear level at your normal listening position.

Otherwise, place the microphone at ear level using a table or a chair.

HOME MENU

RETURN

PTY

BAND

MUTE

Press

The Home Menu appears on your TV. Use and ENTER on the remote

PRESET

TUNE

control to navigate through the screens and select menu items. Press RETURN to exit

the current menu.

• Since the S-HV600B/S-HV500-LR/S-SL100-LR/S-SL100CR are designed as compact

satellite speakers, it is recommended that they be used in combination with a

subwoofer to provide full base sound. In this case, set the X.OVER to 200 Hz here

(see "Change the X.OVER setting" on this page).

Select 'Auto MCACC' from the Home Menu, then press ENTER.

• Mic In! blinks when the microphone is not connected to MCACC SETUP MIC jack.

Try to be as quiet as possible after pressing ENTER. The system outputs a series of

test tones to establish the ambient noise level.

Follow the instructions on-screen.

• When using a powered subwoofer, make sure the subwoofer is on and the volume

is turned up.

Wait for the test tones to ﬁ nish.

A progress report is displayed on-screen while the receiver outputs test tones to

determine the speakers present in your setup. Try to be as quiet as possible while it's

doing this.

• For correct speaker settings, do not adjust the volume during the test tones.

Conﬁ rm the speaker conﬁ guration.

The configuration shown on-screen should reflect the actual speakers you have.

• With error messages (such as Too much ambient noise) select RETRY after

Return

checking for ambient noise.

If the speaker configuration displayed isn't correct, use  to select the speaker and



to change the setting. When you're finished, go to the next step.

If you see an error message (ERR) in the right side column, there may be a problem

with the speaker connection. If selecting RETRY doesn't fix the problem, turn off the

power and check the speaker connections.

The Auto MCACC setup has ﬁ nished! You return to the Home Menu.

Make sure the setup microphone is disconnected.

The settings made in the Auto MCACC setup should give you excellent surround

sound from your system, but it is also possible to adjust these settings manually

Return

using the Manual speaker setup. 

Canceling the demo display

The display on the front panel shows various information (demo displays) when the

receiver is not operating.

You can turn off the demo display. 

• The demo mode is canceled automatically when the Auto MCACC setup is

performed (see below).

RECEIVER

on the remote control, then press the HOME MENU button.

"Manual speaker setup"

"The FL Demo Mode menu"

STANDBY/ ON

PORTABLE /

PHONES

MCACC SETUP MIC

Home Menu

1.Auto MCACC

2.Manual SP Setup

3.Input Assign

4.Pre Out Setting

5.HDMI Setup

6.Auto Power Down

7.FL Demo Mode

1.Auto MCACC

Now Analyzing

Environment Check

Ambient Noise

Speaker YES/NO

Return

1.Auto MCACC

Check!

Front

[ YES ]

Center

[ YES ]

Surr

[ YES ]

Surr. Back

[ - - - ]

[ YES ]

Subwoofer

10:Next

Return

STANDBY/ ON

PHONES

PORTABLE /

MCACC SETUP MIC