Ariston L 63 B-S-W Kullanıcı Kılavuzu - Sayfa 10

Bulaşık Makinesi Ariston L 63 B-S-W için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Ariston L 63 B-S-W 37 sayfaları. Ariston l 63 b na: user guide
Ayrıca Ariston L 63 B-S-W için: Bakım ve Kullanım Kılavuzu (36 sayfalar)

Sayfayı Yazdır

Water in your home

Water hardness varies according to where you live. If the water in your home is hard you have the possibility to

add salt in order to soften your water. The softer the water the better will be your washing and drying results.

Loading the salt.

You can use special water

softening salt or normal rock

salt.

The salt container is situated

underneath the lower rack, fill

it up as follows:

1. Pull out the lower rack

completely, unscrew and

remove the container cap

2. Is it the first time you load

the salt? First fill the

container up with water

(you won't have to do this

again next time)

3. Put the dishwasher funnel

on the hole and pour in

approximately 70 oz. of

salt. It is normal that some

water comes out of the

container.

Troubleshooting

If you have a problem, read this

Your dishwasher may not work or not function properly. In many cases, these are problems which can be solved

without having to call for a technician. Before calling the Customer Care Center, always check the points below.

The dishwasher won't

start

I Is the water supply tap turned

on?

I Is the water supply tap

connected to the hose

properly?

I Has the water in your home

been cut off?

I Is the pressure of the water

supply sufficient?

I Is the hose bent?

I Is the filter on the water supply

hose blocked?

I Is the dishwasher door open?

The dishes are not clean.

I Have you put the right amount

of detergent into the

dispenser?

I Is the wash cycle suitable for

the dishes you have placed

inside the appliance?

I Are the filter and microfilter

clean?

8 ARISTON DISHWASHER - User Manual

Never without salt

4. Screw the cap back in

place carefully.

When should I load the salt?

The salt container must be

filled when the softener

indicator light "S".

Once you have loaded the

salt for the first time, it is

normal that the low salt

indicator light stays on or

flashes for 5 consecutive

cycles.

Intelligent salt.

Your dishwasher can adjust

its

salt

consumption

according to the hardness of

the water in your home. This

way, you can optimise and

customise your dishwasher's

salt consumption (not too

much, nor too little).

To adjust salt consumption,

do as follows:

1. Unscrew the salt container

cap

2. There is an arrow on the

neck of the container (see

figure): if necessary, turn

the arrow anti-clockwise

I Can the sprayer arms turn

freely?

The dishwasher won't drain.

I Is the drain hose bent?

Limescale deposits or a

white film form on the

dishes.

I Is the lid on the salt container

closed properly?

I Is the rinse aid dosage

correct?

Error messages.

Your dishwasher is equipped with

a safety system which is able to

detect any operating problems.

These anomalies are reported by

one or two wash cycle indicator

lights "G" will flash rapidly.

Take a note of which lights are

flashing, turn the appliance off

and call for technical assistance.

Tap off alarm

If you have forgotten to turn the

water tap on, your appliance will

from the "-" setting to the

"+" setting.

Select the arrow position

depending on the water

hardness, referring to the

table provided.

remind you of this by sounding a

few short beeps for a few

minutes.Turn the tap on and your

appliance will start up again after

a few minutes.If you were not

home when these beeps are

sounded,the appliance will be

blocked automatically the 2nd

and 3rd light from the right will

flash rapidly.Turn the appliance

off at the ON-OFF button, turn

on the water tap and wait

approximately 20 seconds before

turning the appliance back on; the

selected wash cycle will start up

again.

Clogged filter alarm

If the appliance is blocked and the

2nd and the 4th light from the right

flash rapidly, this means the filter

is clogged by large particles of

food residue. Turn the appliance

off, clean the filter thoroughly and

reposition it in its seat as

illustrated on page 10. Then turn

it back on. The selected wash

cycle will start up again.

(cycle s\

(O z/cycle )

7 0 o z.)

If you don't know your

water hardness ask your

local water supplier.

NOTE: if you don't find

special water softening

salt you can also use

normal rock salt.

Water load solenoid valve

malfunction alarm.

If the 3rd light from the right

flashes rapidly, turn the

dishwasher off and back on

again after one minute. If the

alarm persists, first turn off the

water tap to avoid any flooding

and then cut off the electricity

supply and call for technical

assistance.

You have checked

everything, but the

dishwasher still doesn't

work and the problem

persists?

Call the Ariston Customer Care

(1-888-426-0825) and remember

to mention:

• the type of malfunction

• the model mark (Mod....) and

the serial number (S/N....)

indicated on the rating plate

located on the inner door, to

one side.