Dinex Smart-Therm STS 3 DXSMA2081 Kullanım ve Bakım Kılavuzu - Sayfa 4
Akü Şarj Cihazı Dinex Smart-Therm STS 3 DXSMA2081 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Dinex Smart-Therm STS 3 DXSMA2081 7 sayfaları.
Sayfayı Yazdır
TROUBLESHOOTING
INFORMATION: Safety-relevant parts should be replaced with
!
original factory parts only. Any defective part must be removed
and replaced by a qualified service technician authorized by
Dinex. Should you require service please call the Dinex Hotline at
1.888.673.4639. In order for the warranty to remain valid, work must
be authorized by Dinex prior to being performed.
The Dinex Smart•Therm STS III Charger is a very intelligent device.
Built in error codes can help you to determine the cause of most
problems.
The following section explains how to determine if you are experiencing
a problem and what can be done to correct the problem. This
information can be very helpful if you are calling our Customer Service
department to report any operational difficulties.
ERROR CODES
Error codes will show on the LCD display. The code will remain on the
display until the problem is fixed and the charger is turned OFF and ON
again.
Error:
Internal Temp Too High, Clean Air Filter
Cause:
Internal temperature of the charger is too high. The
environment it too hot or the unit does not have proper airflow.
Solution: Turn the charger off and allow the unit to cool. Inspect the air
filter and clean if needed. Remove any obstruction that
prevents proper airflow.
.
Error:
Input Voltage Low/Overload
Cause:
Input voltage or frequency not within the proper range as noted
on the unit nameplate.
Solution: Turn the charger off. Check the input voltage and frequency of
the dedicated circuit being used. Only use with a circuit that
provides the proper power.
Error:
E0 Base Detection Error
Cause:
The charger is not capable of detecting a base on the surface.
Solution: Call Dinex Service at 1.888.673.4639.
Error:
E2 RFID Error
Cause:
The RFID reader or antenna is not able to read the tag and
charge the base.
Solution: Call Dinex Service at 1.888.673.4639.
MAINTENANCE
Smart•Therm STS III CHARGER CLEANING INSTRUCTIONS
1.
Unplug the charger before cleaning. Do not submerge the charger in
water. Do not splash or pour water onto the charger's control panel
or into intake/outlet vents. Possible shock hazard may result and the
charger may be damaged.
2.
The heating surface is a high strength composite material. Please
use appropriate care in handling and cleaning.
3.
Do not use steel wool, abrasive cleaners, or chlorinated cleaners on
the charger.
4.
Wipe the entire charger off with a damp cloth and mild detergent.
Dry the charger before connecting it to its electrical source.
AIR FILTER
1. Inspect the mesh air filter on the underside of the unit each day. If
soiled, remove the filter and wash with hot water, dish washing
detergent and a scrub brush. Cleaning in a dishwasher is not
recommended. Dry and reattach to the unit before operating.
2. If using the unit daily, the recommended filter replacement period is
every 6 months. The preprogrammed message "MAINTENANCE
REPLACE AIR FILTER" will show on the display every 6 months as
a reminder. To clear this message, simply turn the unit OFF and ON
again.
4.
Replacement filter can be ordered by calling Dinex customer service
at 1.888.673.4639. item number DXFTNSMA208.
WARNING: Never spray, wash or use excessive water on the
!
charger. Before cleaning it is absolutely necessary to unplug power
plug.
• Do not use the charger if the top is broken or cracked.
• Never use the charger as a work surface or cutting board.
• Never attempt to heat anything other than a Dinex
8x1-Series Smart base.
WARRANTY
These Warranties cover the following Dinex | Carlisle ("Dinex")
equipment products (the "Warranted Products"):
• Rethermalization Equipment Products
• Induction Heating System Products (excluding Induction Bases
covered under separate warranty)*
• Milk Cooler Products
• Ice Cream Freezer Products
• Air Curtain Refrigerator Products
• Blast Chiller Products
• Hot/Cold Food Counter Products
• Plate, Rack and Tray Dispenser Products
• Plate Heater Products
• Base Heater Products
• Drying and Storage Rack Products
• Starter Station Products
• Conveyer Products
• Tray and Other Cart Products
Warranted Products also includes any other Equipment System
Products identified on Dinex's website (www.dinex.com) from time to
time.
Standard Warranty. Except as indicated otherwise below, Dinex
warrants that the Warranted Products will be free from defects in title,
material and workmanship under normal use and service and will
perform substantially in accordance with Dinex's written technical
specifications for the Warranted Products (as such specifications
exist on the date the Warranted Products are shipped) (the "Product
Specifications") . This warranty covers both parts and labor and
is available only to end-users (the "Customers") that purchase the
Warranted Products from Dinex or its authorized distributors. For the
purpose of these warranties, a defect is determined by Dinex after its
good faith investigation.
Dinex Software. In addition to the other warranties set forth herein, with
respect to Dinex's licensed software, Dinex warrants that it has the right
to license or sublicense the software to Customer for the purposes and
subject to the terms and conditions set forth in Dinex's standard terms
and conditions.
Smart•Therm STS III | 4