Ariston PH 640 Kullanım Talimatları Kılavuzu - Sayfa 3

Hob Ariston PH 640 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Ariston PH 640 12 sayfaları.
Ayrıca Ariston PH 640 için: Kullanım Talimatları Kılavuzu (14 sayfalar)

Sayfayı Yazdır

Ariston PH 640 Kullanım Talimatları Kılavuzu

Hooking position

for top H=40 mm

! Use the hooks contained in the "accessory pack"

• Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This must

be placed at a minimum distance of 20 mm from the

lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the oven

so that it rests on two strips of wood, or on a completely flat

surface with an opening of at least 45 x 560 mm ( see

diagrams ).

When installing the cooktop above a built-in oven

without forced ventilation, ensure that there are air

inlets and outlets for ventilating the interior of the

cabinet adequately.

Electrical connection

Hobs equipped with a three-pole power supply cable are

designed to operate with alternating current at the voltage

and frequency indicated on the data plate (this is located on

the lower part of the appliance). The earth wire in the cable

has a green and yellow cover. If the appliance is to be

installed above a built-in electric oven, the electrical

connection of the hob and the oven must be carried out

separately, both for electrical safety purposes and to make

extracting the oven easier.

Front

Back

Connecting the supply cable to the mains

Fit the supply cord with a standard plug for the

demand rate indicated on the rating plate or connect

it directly to the electrical mains. In the latter case, a

single pole switch must be placed between the

appliance and the mains, with a minimum opening

between the contacts of 3 mm in compliance with

current safety codes (the earthing wire must not be

interrupted by the switch). The power supply cord

must be positioned so that it does not reach a

temperature in excess of 50°C above room

temperature at any point.

Before making the actual connection, make sure

that:

• The fuse and electrical system can withstand the

load required by the appliance;

• That the electrical supply system is equiped with

an efficient earth hook-up according to the norms

and regulations prescribed by law;

• That the plug or switch is easily accessible.

! the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow

Blue

Brown

As the colours of the wires in the mains lead may

not correspond with the coloured markings

identifying the terminals in your plug, proceed as

follows:

Connect the Green & Yellow wire to the terminal

marked "E E E E E " or

or coloured Green or Green &

Yellow.

Connect the Brown wire to the terminal marked "L L L L L " or

coloured Red.

Connect the Blue wire to the terminal marked "N N N N N " or

coloured Black.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only ( see Assistance ).

! The manufacturer declines any liability should these safety

measures not be observed.

Gas connection

The appliance should be connected to the main gas supply

or to a gas cylinder in compliance with current national

regulations. Before carrying out the connection, make sure

the cooker is compatible with the gas supply you wish to

use. If this is not the case, follow the instructions indicated in

the paragraph "Adapting to different types of gas."

When using liquid gas from a cylinder, install a pressure

regulator which complies with current national regulations.

- Earth

- Neutral

- Live