Whirlpool 2DLSQ8000JQ3 Kullanım ve Bakım Kılavuzu - Sayfa 9
Yıkayıcı Whirlpool 2DLSQ8000JQ3 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Whirlpool 2DLSQ8000JQ3 20 sayfaları. Easy-to-use automatic washers
Sayfayı Yazdır
First try the solutions suggested here and possibly avoid the cost of a service call...
Washer won't fill, rinse or agitate
Check the following:
Is the power cord plugged in?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Does the water level seem too low, or does the washer
appear to not fill completely?
The top of the agitator is much higher than the highest water
level. This creates a perception that the washer is not filling
completely. This is normal.
Is the lid open?
The lid must be closed during operation. Washer will not
agitate or spin with the lid open.
Washer stops
Check the following:
Is the power cord plugged in?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Is there power at the plug?
Check your electrical source or call an electrician.
Has a fuse blown or is the circuit breaker open?
If problem continues, call an electrician.
Are you using an extension cord?
Do not use an extension cord.
Is the washer in a normal pause in the Casual/Permanent
Press (or Hand Washables) cycle?
The washer pauses for about 2 minutes in the Casual/
Permanent Press cycle. Allow the cycle to continue.
The Hand Washables cycle (on some models) features
periods of agitation and soak.
Is the lid open?
The lid must be closed during operation. Washer will not
agitate or spin with the lid open.
Is the washer overloaded?
Wash smaller loads.
TROUBLESHOOTING
Washer won't drain or spin
Is the drain hose clogged, or the end of the drain hose
more than 72 in. (183 cm) above the floor?
See the Installation Instructions for proper installation of drain
hose.
Is the lid open?
The lid must be closed during operation. Washer will not
agitate or spin with the lid open.
Is there excessive sudsing?
Always measure detergent. Follow manufacturer's directions.
If you have very soft water, you might need to use less
detergent.
Is your voltage low?
Check your electrical source or call an electrician. Do not use
an extension cord.
Washer continues to fill or drain, or the cycle seems
stuck
Is the top of drain hose lower than the water level in
washer?
The top of the hose must be higher than the water level in the
washer for proper operation. See the Installation Instructions.
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal
the drain hose with tape. The hose needs an air gap. See the
Installation Instructions.
Washer makes noise
Is the load balanced and the washer level?
The wash load should be balanced and not overloaded.
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs
(if needed). See the Installation Instructions.
Did you completely remove the yellow shipping strap with
cotter pins?
See the Installation Instructions.
Are the gears engaging after the drain and before spin, or
is the upper part of agitator clicking during wash?
These are normal washer noises.
9