Whirlpool 7MLSR6232JT2 Kullanım ve Bakım Kılavuzu - Sayfa 9

Yıkayıcı Whirlpool 7MLSR6232JT2 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Whirlpool 7MLSR6232JT2 28 sayfaları. Whirlpool automatic washers use & care guide

Sayfayı Yazdır

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid

the cost of a service call...

Washer won't fill, rinse or agitate

Check the following:

Is the power cord plugged into a grounded 3 prong outlet?

Is the indicator on the Cycle Control knob properly lined up

with a cycle? Turn the Cycle Control knob to the right slightly

and pull to start.

Are the water inlet valve screens clogged?

Are both the hot and cold water faucets turned on?

Is the water inlet hose kinked?

Does the water level seem too low, or does the washer

appear to not fill completely?

The top of the agitator is much higher than the highest water

level. This creates a perception that the washer is not filling

completely. This is normal.

Washer stops

Check the following:

Is the power cord plugged into a grounded 3 prong outlet?

Is the indicator on the Cycle Control knob properly lined up

with a cycle? Turn the Cycle Control knob to the right slightly

and pull to start.

Are the water inlet valve screens clogged?

Are both the hot and cold water faucets turned on?

Is the water inlet hose kinked?

Is there power at the plug?

Check your electrical source or call an electrician.

Has a fuse blown or is the circuit breaker open?

If problem continues, call an electrician.

Are you using an extension cord?

Do not use an extension cord.

Is the washer in a normal pause in the Casual/Planchado

Permanente (Casual/Permanent Press) (or Delicado

[Gentle])cycle?

The washer pauses for about 2 minutes in the Casual/

Planchado Permanente (Casual/Permanent Press) cycle.

Allow the cycle to continue.

The Delicado (Gentle) cycle (on some models) features

periods of agitation and soak.

Is the lid open?

The lid must be closed during operation.

Is the washer overloaded?

Wash smaller loads.

Washer won't drain or spin

Is the drain hose clogged, or the end of the drain hose

more than 96 in. (2.4 m) above the floor?

See the Installation Instructions for proper installation of drain

hose.

Is the lid open?

The lid must be closed during operation.

Is there excessive sudsing?

Always measure detergent. Follow manufacturer's directions.

If you have very soft water, you might need to use less

detergent.

Is your voltage low?

Check your electrical source or call an electrician. Do not use

an extension cord.

Washer continues to fill or drain, or the cycle seems stuck

Is the top of drain hose lower than the water level in

washer?

The top of the hose must be higher than the water level in the

washer for proper operation. See the Installation Instructions.

Does the drain hose fit too tightly in the standpipe, or is it

taped to the standpipe?

The drain hose should be loose yet fit securely. Do not seal

the drain hose with tape. The hose needs an air gap. See the

Installation Instructions.

Washer makes noise

Is the load balanced and the washer level?

The wash load should be balanced and not overloaded.

The washer must be level. The front feet should be properly

installed and the nuts tightened. Reset the rear leveling legs

(if needed). See the Installation Instructions.

Did you completely remove the yellow shipping strap with

cotter pins?

See the Installation Instructions.

Are the gears engaging after the drain and before spin, or

is the upper part of agitator clicking during wash?

These are normal washer noises.

Washer leaks

Check the following:

Are the fill hoses tight? Are the fill hose washers properly

seated? Is the drain hose clamp properly installed? See the

Installation Instructions.

Is the sink or drain clogged?

Sink and standpipe must be able to handle 17 gal. (64 L) of

water per minute.

Is water deflecting off the tub ring or the load?

Center the tub before starting the washer.

The wash load should be balanced and not overloaded. The

fill or spray rinses can deflect off the load.

The washer must be level. The front feet should be properly

installed and the nuts tightened. Reset the rear leveling legs

(if needed). See the Installation Instructions.

Check household plumbing for leaks.