Ariston PH 760 RF GH Kullanıcı Kılavuzu - Sayfa 8

Hob Ariston PH 760 RF GH için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Ariston PH 760 RF GH 11 sayfaları. Ariston hob

Sayfayı Yazdır

replaced (supplied with the appliance).

The feeding connector of the gas to the appliance is

threaded 1/2 gas male cylinder.

Connection to flexible steel tube

The gas feed connector to the appliance is a threaded,

male 1/2" connector for round gas pipe. Only use pipes

and sealing gaskets that that conform to the standards

currently in force. The maximum length of the flexible pipes

must not exceed 2000 mm. Once the connection has been

made, ensure that the flexible metal tube does not touch

any moving parts and is not crushed.

Check the Seal

Once the appliance has been installed, make sure all the

connections are properly sealed, using a soapy water

solution. Never use a flame.

Electrical Connection

The cooktops fitted with a tripolar electrical supply cord

are designed to be be used with alternating current

according to the indications on the rating plate located

under the cooktop. The earthing wire can be identified by

its yellow-green colour.

In the case of installation over a built-in electric oven,

the electrical connections for the cooktop and oven

should be independent, not only for safety purposes, but

also to facilitate removal of one or both in the future.

Electrical Connection for Gas Cooktop

Fit the supply cord with a standard plug for the demand

rate indicated on the rating plate or connect it directly to

the electrical mains. In the latter case, a single pole switch

must be placed between the appliance and the mains,

with a minimum opening between the contacts of 3 mm in

compliance with current safety codes (the earthing wire

must not be interrupted by the switch). The power supply

cord must be positioned so that it does not reach a tem-

perature in excess of 50°C above room temperature at

any point.

Before actual connection make sure that:

•

The fuse and electrical system can withstand the load

required by the appliance;

•

That the electrical supply system is equiped with an

efficient earth hook-up according to the norms and

regulations prescribed by law;

•

That the plug or switch are easily accessible.

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow

Blue

Brown

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to terminal marked "E"

or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked "L" or

coloured Red.

Connect the Blue wire to the terminal marked "N" or

coloured Black.

- Earth

- Neutral

- Live

Adapting the Cooktop for Different Types of Gas

To adapt the cooktop to a different type of gas than that

for which it was designed, (see the sticker under the hob

or on the packaging), the burner nozzles must be changed,

as follows:

•

Remove the pan supports and slide the burners out of

the cooktop.

•

Unscrew the nozzles using a 7mm socket wrench and

replace them with those for the new type of gas. (See

table 1, "Burner and Nozzle Specifications").

•

Reassemble the parts following the instructions in

reverse order.

•

On completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker

is available from our Service Centres.

If the gas pressure is different than that prescribed, a

pressure regulator must be installed at the source, in

compliance with national standards governing the use of

piped gas regulators.

Replacing the nozzles on separate "double flame "

burners:

•

remove the grids and slide the burners from their

housings. The burner consists of 2 separate parts (Fig.

E and fig. F);

•

unscrew the burers with a 7 mm wrench spanner. The

internal burner has a nozzle, the external burner has

two (of the same size). Replace the nozzle with models

suited to the new type of gas (see table 1).

•

replace all the components by repeating the steps in

reverse order.

Fig. E

Regulation of Air Supply to the Burner

The burners do not need a primary air regulator.

Minimum Regulation

Minimum regulation:

•

Turn the gas valve to minimum.

•

Remove the knob and turn the regulator screw

clockwise until the flame becomes small but regular.

N.B.: In the case of liquid gas, the regulation screw must

be fully screwed in (clockwise).

Fig. F