Whirlpool 8182192 Kullanım ve Bakım Kılavuzu - Sayfa 7

Yıkayıcı Whirlpool 8182192 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Whirlpool 8182192 44 sayfaları. Front-loading automatic washer

Sayfayı Yazdır

GROUNDING

iNSTRUCTiONS

For a grounded,

cord-connected

washer:

This washer

must be grounded.

Unthe event of a

maffunction

or breakdown,

grounding

wHUreduce

the

risk of eUectdcaU shock by providing

a path of Ueast

resistance

for eUectric current.

This washer

equipped

with a cord having

an equipment-grounding

conductor

and a grounding

pUug. The pUug must be

pUugged into an appropriate

outUet that is properUy

installed

and grounded

in accordance

with aH UocaU

codes

and ordinances.

WARNING:

Umproper connection

of the

equipment-grounding

conductor

can resuUt in a risk of

eUectric shock.

Check with a qualified

eUectrician or

serviceman

if you are in doubt as to whether

the

appliance

is properly

grounded.

Do not modify

the plug provided

with the appliance

if it will not fit the outlet, have a proper outlet

installed

by a qualified

electrician.

For a permanently

connected

washer:

This washer

must be connected

to a grounded

metal,

permanent

wiring system,

or an equipment

grounding

conductor

must be run with the circuit conductors

and

connected

to the equipment-grounding

terminal

lead on the appliance.

There are 4 bolts in the rear panel of the washer that support the

suspension system during transportation.

These bolts also retain

the power cord inside the washer until the bolts are removed.

Using a 13 mm wrench, loosen each of the bolts.

Once the bolt is loose, move it to the center of the hole and

completely pull out the bolt, including the plastic spacer

covering the bolt. The power cord will be attached to all

4 bolts inside the washer.

3. Once all 4 bolts are removed, pull the power cord through the

opening of the rear panel and close the hole with the attached

cap.

4. Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported

at a later date, call your

local service center.

INSTALLATION

INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

washer.

Failure to do so can result in back or other injury.

IMPORTANT:

Position the washer so that the rear of the unit is

within approximately

3 ft (90 cm) of the final location.

Connect

the inlet hoses to the water

faucets

Make sure the washer drum is empty.

1. Using pliers, check the tightness of the hose couplings

already attached to the washer.

NOTE: Do not overtighten. Damage to the coupling can result.

2. Attach the hose with the red color indicator to the hot water

faucet. Screw on coupling by hand until it is seated on the

washer.

3. Attach the hose with the blue color indicator to the cold water

faucet. Screw on coupling by hand until it is seated on the

washer.

4. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten.

Damage to the coupling can

result.

Turn on the water faucets and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.