Whirlpool AWE 2217 Program Tablosu - Sayfa 2
Yıkayıcı Whirlpool AWE 2217 için çevrimiçi göz atın veya pdf Program Tablosu indirin. Whirlpool AWE 2217 2 sayfaları.
Ayrıca Whirlpool AWE 2217 için: Programlama Kılavuzu (2 sayfalar)
Sayfayı Yazdır
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton**
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
40
Quick wash
30
Wool
40
Handwash
40
Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in
compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to
the water supply pressure and temperature, the load and the type of wash.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water
out.
** Reference Programme for Energy Label.
PREPARATION OF THE WASH CYCLE
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent and additives into the dispenser to
no more than the "MAX" level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Stain remover agents
• Anti-scale agents (if necessary)
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The lamp next to the
"Start/Pause" button flashes.
Load
Water
Energy
Approx. Programme
Duration
(kg)
(l)
(kWh)
(hours : minutes)*
5.0
50*
1.70
5.0
45
0.95
5.0
55
0.55
2.5
50*
0.80
2.5
45
0.45
1.5
50
0.55
3.0
35
0.40
1.0
55
0.55
1.0
40
0.40
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
"Intensive rinse" button
• The amount of water is increased to ensure a more
intensive rinse.
• This option is particularly suitable for areas with very
soft water, washing baby linen and people with skin
allergies.
"Spin speed reduction" button
• Reduces the predetermined automatic maximum
spin speed to treat your laundry more gently.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The indication lamp next to the "Start/Pause" button
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
2:05
through Wash, Rinse, Spin/Drain. When the programme
2:10
phrase is finised, the corresponding indication goes out.
2:00
•
Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
1:30
programme will run again from the point where it
1:15
was interrupted.
0:45
"DOOR OPEN" INDICATION
0:30
Before starting and after end of a programme, the lamp
0:45
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
0:35
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to "Cancel (Reset) a running programme before
the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused
by a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your "Instructions for Use";
if the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
"Troubleshooting Guide" in the Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use ("Removing
the Filter").
PROGRAMME END
•
All the lights of the programme sequence indicator
are off, and the "Door open" indication lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The "Reset" button cancels a programme before the
end. Press the "Reset" button for at least 3 seconds.
Any existing water is drained out before the door can be
opened.
Whirlpool is a registered trademark of Whirlpool USA.
5019 312 10561