Whirlpool 3979171 Kurulum Talimatları Kılavuzu - Sayfa 7
Kurutucu Whirlpool 3979171 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Whirlpool 3979171 8 sayfaları.
Sayfayı Yazdır
Before you start:
Your safety and the safety of others
is very important.
We have provided many important safety messages
in this manual and on your appliance. Always read
and obey all safety messages.
This is the safety alert symbol. This
symbol alerts you to hazards that can kill
or hurt you and others. All safety
messages will be preceded by the safety alert symbol
and the word "DANGER" or "WARNING". These
words mean:
DANGER
You will be killed or seriously injured if you don't
follow instructions.
WARNING
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will identify the hazard, tell
you how to reduce the chance of injury, and tell you
what can happen if the instructions are not
followed.
Check that you have everything necessary for correct
installation. Proper installation is your responsibility.
Tools needed:
• #2 Phillips screwdriver
• safety glasses
• flat-blade screwdriver
• caulking gun and
compound (new vent
• adjustable wrench that
installation)
opens to 1" or 1" hex-
head socket wrench (for
• gloves
adjusting dryer feet)
• tin snips (new vent
• level
installations)
• wire stripper (direct wire
installations)
Part No. 3979171
© 2001 Whirlpool Corporation
Parts supplied:
Remove parts package from
dryer drum. Check that all 4
legs were included.
4 leveling legs
Parts needed:
Check local codes and see electrical and venting
requirements, Panels A and B, before purchasing parts.
Determine if you will need to purchase a power
supply cord kit or power supply cable.
Electrical
If using a power supply cord:
Dryer power supply cord must be:
• U.L.-listed
• 30-ampere
• 120/240-volt
• Type SRD or SRDT
minimum
• At least 4 feet long
The wires that connect to the dryer must end in ring
terminals or spade terminals with upturned ends.
The receptacle must be located within 3 feet of the
top, back center of the control console.
If your outlet
Choose this
looks like this:
power supply cord:
4-wire receptacle
4-wire power supply cord with
(14-30R)
ring or spade terminals and
U.L.-listed strain relief
3-wire receptacle
3-wire power supply cord with
(10-30R)
ring or spade terminals and
U.L.-listed strain relief
If connecting by direct wire:
Power supply cable must match power supply
(4-wire or 3-wire) and be:
• flexible armored or non-metallic sheathed copper
cable (with ground wire). All current-carrying wires
must be insulated. See Panels D and E.
• 10-GAUGE SOLID COPPER WIRE. (Do not use
aluminum.)
• at least 4 feet long.
Benton Harbor, Michigan 49022
Venting
WARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can
result in death or fire.
Four-inch heavy metal exhaust vent and clamps
must be used. Dura Safe™ vent products are
recommended.
Dura Safe vent products can be purchased from your
dealer or by calling Whirlpool Parts & Accessories
1-800-442-9991, Mon-Fri: 8am to 9pm (CST), Sat:
9am to 4:30pm (CST). Visit our internet site at
http://www.whirlpoolappliances.com/accessories
See Panel C for more information.
Exhaust hood
Do Not use exhaust hoods with magnetic latches.
Preferred
Acceptable
4"
4"
Mobile home installations require:
• Mobile Home Installation Kit, Part Number 346764*
• Metal exhaust system hardware*
Floors sloped greater than 1 inch:
Require Extended Dryer Feet Kit, Part No. 279810*
*
Available for purchase from your dealer.
2-1/2"
Printed in U.S.A.