Whirlpool 8533582 Kullanım ve Bakım Kılavuzu - Sayfa 7

Kurutucu Whirlpool 8533582 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Whirlpool 8533582 24 sayfaları. Duet electronic electric dryer

Sayfayı Yazdır

Electrical Requirements

It is your responsibility

To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

The National Electric Code requires a 4-wire supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240-volt,

60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The green cabinet-grounding

conductor is permanently connected to the neutral conductor

(white wire) within the dryer. If the dryer is installed with a

4-wire electrical supply connection, the green cabinet-

grounding conductor must be removed from the external

ground conductor screw (green screw), and secured under

the neutral terminal (center or white wire) of the terminal

block. When the green cabinet-grounding conductor is

secured under the neutral terminal (center or white wire) of

the terminal block, the dryer cabinet is isolated from the

neutral conductor.

If local codes do not permit the connection of a cabinet

ground connector to the neutral wire, see "Optional 3-wire

connection" section.

Use a 4-wire conductor cord when the dryer is installed in a

mobile home or an area where local codes do not permit

grounding through the neutral.

If using a power supply cord:

Use a UL approved power supply cord kit marked for use with

clothes dryers. The kit should contain:

A UL approved 30 amp power supply cord, rated

120/240-volt minimum. The cord should be type SRD or

SRDT and be at least 4 ft (1.22 m) long. The wires that

connect to the dryer must end in ring terminals or spade

terminals with upturned ends.

A UL approved strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade

terminals and UL approved strain relief. The 4-wire power supply

cord, at least 4 ft (1.22 m) long, must have 4, 10-gauge solid

copper wires and match a 4-wire receptacle of NEMA Type

14-30R. The ground wire (ground conductor) may be either green

or bare. The neutral conductor must be identified by a white

cover.

If your outlet looks like this:

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade

terminals and UL approved strain relief. The 3-wire power supply

cord, at least 4 ft (1.22 m) long, must have 3, 10-gauge solid

copper wires and match a 3-wire receptacle of NEMA Type 10-

30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with flexible metallic conduit. All

current-carrying wires must be insulated.

10-gauge solid copper wire (do not use aluminum).

At least 5 ft (1.52 m) long.

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This

dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

For a permanently connected dryer:

This dryer must be connected to a grounded metal, permanent

wiring system, or an equipment-grounding conductor must be

run with the circuit conductors and connected to the

equipment-grounding terminal or lead on the dryer.

WARNING:

Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.