Whirlpool 8578185 Kullanım ve Bakım Kılavuzu - Sayfa 18

Kurutucu Whirlpool 8578185 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Whirlpool 8578185 28 sayfaları. Electronic electric dryer

Sayfayı Yazdır

Press the WRINKLE SHIELD™ feature button if this

option is desired.

Press the END OF CYCLE SIGNAL button to set signal

volume to desired level.

Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

Once an Automatic cycle has started, the WRINKLE

SHIELD™ feature and cycle signals can be adjusted. Press

the PAUSE/CANCEL key twice to stop the dryer and clear the

settings, allowing you to select another cycle and Dryness

Level.

How Automatic Cycles Work

EvenHeat™ improves drying performance with Auto Moisture

Sensing Plus, which advances the cycle as moisture is

extracted from clothing. A thermistor (electronic temperature

sensor) and moisture sensing strips in the dryer drum help

measure the amount of moisture in the clothes as they pass.

An electronic control determines the load type to help save

time, avoid overdrying, and increase the accuracy of the end

dryness level. After the first 5 minutes of an automatic cycle,

the estimated time display will adjust based on the

approximate load size, cycle, dryness level selected and

amount of moisture left in the clothes. When the clothes have

reached approximately 80% of the dryness level selected, the

estimated time display will adjust again, showing the final

drying time. Auto Moisture Sensing Plus takes the guesswork

out of drying time and enhances fabric care.

To use a Manual Cycle

Rotate the dial to select a Manual Cycle.

Press MORE TIME or LESS TIME until the desired drying time

is displayed. Tap MORE TIME or LESS TIME, and the time will

change by 1-minute intervals. Press and hold MORE TIME or

LESS TIME, and the time will change by 5-minute intervals.

The initial time displayed is the actual drying time.

NOTE: The More Time or Less Time feature can be used only

with Manual Cycles.

Press TEMPERATURE until the desired temperature

glows.

NOTE: Pressing the Dryness Level button will cause the triple

beep indicating that this option is not selectable. Also, a

Dryness Level is not indicated.

Press the WRINKLE SHIELD™ feature button if this

option is desired.

Press the END OF CYCLE SIGNAL button to set volume

to desired level.

Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

While a Manual Cycle is running, you can change the settings

for Time, Temperature, the WRINKLE SHIELD™ feature and

the cycle signals. Press the PAUSE/CANCEL key twice to

stop the dryer and clear the settings, allowing you to select

another cycle.

Stopping Your Dryer

To stop your dryer at any time

Press PAUSE/CANCEL twice or open the door.

Pausing or Restarting

To pause the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door and press (and hold) HOLD TO START button until

dryer starts.

NOTE: Drying will continue from where the cycle was interrupted,

if you close the door and press Start within 5 minutes. If the cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

Control Locked

This feature allows you to lock your settings to avert unintended

use of the dryer. You can also use the Control Locked feature to

avert unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is

running:

Press and hold the END OF CYCLE SIGNAL button for

3 seconds. The control is locked when a single beep is heard and

the Control Locked status light is on.

When the dryer is off, it is not necessary to press the Control

On button before activating the Control Locked feature.

To unlock:

Press and hold the END OF CYCLE SIGNAL button for 3 seconds

to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the

dryer can be stopped by pressing the Pause/Cancel button, but

can't be restarted until the control is unlocked.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your

load. If an Automatic Cycle is running, the display shows the

estimated cycle time when your dryer is automatically sensing

the dryness level of your load. If a Manual Cycle is running, the

display shows the exact number of minutes remaining in the

cycle.

Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

Follow care label directions when they are available.

If desired, add a fabric softener sheet. Follow package

instructions.

Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits, and synthetic fabrics.

Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased

shrinking or wrinkling.

If you dry sheets in a mixed load or large items in the Bulky

Items cycle, rearrange the load when the signal sounds. This

will aid in the drying process.