Whirlpool Cabrio WGD6600VW0 Kullanım ve Bakım Kılavuzu - Sayfa 22
Kurutucu Whirlpool Cabrio WGD6600VW0 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Whirlpool Cabrio WGD6600VW0 48 sayfaları. Steam fabric care system gas dryer
Ayrıca Whirlpool Cabrio WGD6600VW0 için: Parça Listesi (8 sayfalar)
Sayfayı Yazdır
feel air movement,
clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See the
Installation Instructions.
9
_ ± t,
Explosion
Hazard
Keep flammable
materials
and vapors,
such as
gasoline,
away from dryer.
Place dryer at Neast 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, expNosion, or fire.
•
Are fabric softener sheets blocking
the grille?
Use only one fabric softener sheet, and use it only once.
Is the exhaust vent the correct
length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
Installation Instructions.
•
Is the exhaust vent diameter the correct
size?
Use 4" (10.2 cm)diameter
vent material.
Is the dryer located in a room with temperature
below
45°F (7°C)?
Proper operation of dryer cycles requires temperatures
above
45°F (7°C).
Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. The rear of the dryer requires 51_z"(14 cm)
of airspace, and the sides and front of the dryer require a
minimum of 1" (2.5 cm). See the Installation Instructions.
Has the Air Only modifier
been selected?
Select the right temperature for the types of garments being
dried. See "Modifiers."
•
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
•
Are clothes coming out of the Quick Refresh cycle with
damp or wet spots?
Under certain environmental
or installation conditions you
may experience underdrying.
Select the Timed Dry cycle
(20 min. default time), which can be customized
by choosing
temperature by pressing TEMP and/or cycle time by pressing
the Time Adjust up or down buttons.
Cycle time too short
Excessive
Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
•
Is the automatic
cycle ending early?
The load may not be contacting
the sensor strips. Level the
dryer.
Change the dryness level setting on Automatic
Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
Lint on load
•
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Stains on load or drum
•
Was dryer fabric softener
properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets in the
Enhanced Touch Up or Quick Refresh Steam cycles.
Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
Loads are wrinkled
•
Was the load removed from dryer at the end of the cycle?
Select Enhanced Touch Up Cycle to tumble the load with
water and heat to help smooth out wrinkles from a load left in
the dryer.
Was the dryer overloaded?
Dry smaller loads that can tumble freely. Smaller loads of
one to four garments yield best results with Quick Refresh
Cycle. Results may also vary depending
on fabric type. This
cycle is best for reducing wrinkles and odors from loads
consisting
of wrinkle-free cotton, cotton polyester blends,
common knits and synthetics.
Loads are still wrinkled following
SteamCare cycle?
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer's water
inlet valve. Check that the water supply is turned on. This
cycle is best for smoothing out wrinkles and reducing odors
from loads consisting of wrinkle-free
cotton, cotton polyester
blends, common knits and synthetic garments.
NOTE: Refer to garment care label instructions. Dry clean
only garments are not recommended.
Odors
•
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
Is water connected
to the dryer?
Check that water inlet hose is connected to both the faucet
and dryer's water inlet valve. Check that the water supply is
turned on.
To remove odors left in garments after wearing, select Quick
Refresh Cycle for small loads of one to four garments. This
cycle is best for reducing and odors from loads consisting of
wrinkle-free cotton, cotton polyester blends, common knits
and synthetics.
22