Whirlpool Cabrio,- WGD5500X Boyutlar ve Kurulum - Sayfa 2

Kurutucu Whirlpool Cabrio,- WGD5500X için çevrimiçi göz atın veya pdf Boyutlar ve Kurulum indirin. Whirlpool Cabrio,- WGD5500X 2 sayfaları. Whirlpool 29" and 27" wide model gas dryer
Ayrıca Whirlpool Cabrio,- WGD5500X için: Kullanım ve Bakım Kılavuzu (28 sayfalar), Ürün Boyutları (1 sayfalar)

Sayfayı Yazdır

Whirlpool Cabrio,- WGD5500X Boyutlar ve Kurulum

INSTALLATION REQUIREMENTS

GAS SUPPLY REQUIREMENTS

Gas supply

This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should be 1/2" IPS. When

acceptable to the gas supplier and local codes, 3/8" approved tubing may be used for lengths under 20 ft (6.1 m). For lengths over 20 ft (6.1 m), larger

tubing should be used. Pipe-joint compounds resistant to the action of L.P. gas must be used. An individual manual shutoff valve must be installed

within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Z223.1.

ELECTRICAL REQUIREMENTS

A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required. A time-delay fuse or circuit breaker and a separate circuit

are recommended.

VENTING REQUIREMENTS

Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm)

diameter vent is required. Rigid or flexible metal exhaust vent

must be used. Do not use plastic or metal foil vet. Exhaust hood

must be at least 12" (305 mm) from the ground or any object that

may be in the path of the exhaust.

Exhaust hoods:

Recommended Styles:

Louvered Hood

Acceptable Style:

Angled Hood

Determine vent path:

Select route that will provide straightest and most direct

■

path outdoors.

Plan installation to use fewest number of elbows and turns.

■

When using elbows or making turns, allow as much room

■

as possible.

Bend vent gradually to avoid kinking.

■

Use as few 90° turns as possible.

■

Determine vent length and elbows needed for best

drying performance:

Use following Vent System Chart to determine type of vent

■

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified

in Vent System Chart. Exhaust systems longer than those

specified will:

Shorten life of dryer.

■

Reduce performance, resulting in longer drying times

■

and increased energy usage.

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Box Hood

The "Vent System Chart" provides venting requirements that

will help achieve best drying performance.

Vent System Chart

Number of

Type

of vent

90° turns or

elbows

Rigid metal

NOTE: Side and bottom exhaust installations for 27" wide

models have a 90º turn inside the dryer. To determine

maximum exhaust length, add one 90º turn to the chart.

Vent System Chart

(29" Wide Long Vent Models Only)

Number of

Type

90° turns

of vent

or elbows

Rigid metal

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Box/louvered

Angled

hoods

58 ft. (17.7 m)

64 ft. (20 m)

54 ft. (16.5 m)

48 ft. (14.6 m)

44 ft. (13.4 m)

38 ft. (11.6 m)

35 ft. (10.7 m)

29 ft. (8.8 m)

27 ft. (8.2 m)

21 ft. (6.4 m)

Box/louvered, or

Angled hoods

120 ft. (36.6 m)

110 ft. (33.5 m)

100 ft. (30.5 m)

90 ft. (27.4 m)

80 ft. (24.4 m)

70 ft. (21.3 m)