Whirlpool CGM2761TQ0 Kurulum Talimatları Kılavuzu - Sayfa 10

Kurutucu Whirlpool CGM2761TQ0 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Whirlpool CGM2761TQ0 36 sayfaları. Commercial gas or electric dryer

Sayfayı Yazdır

INSTALLATION INSTRUCTIONS- GASDRYER

iii_ii:i!!ii_ii:iii_iiiiiiiii

,_iii_i_iiii_!i_

i!!i!!iiiii_i,ii!ii_i!':

¸i_i:ii:i_iifd

'_il :i_i:!d!!i_

il!!i,_i:iii_i_:

The console houses the factory-installed

accumulator timer with

1°

actuating arm and button.

The factory-installed

timer is set to provide 45 minutes (4 pins) of

drying time when activated by the coin slide. Timer cams for

30-minute (6 pins) and 60-minute (3 pins) drying times are

included in the parts bag.

The coin slide mechanism, control panel lock and key, and coin

box lock and key are not included and are available from usual

industry sources.

NOTE: Slide dryer onto cardboard or hardboard before moving to

avoid damaging floor covering.

1. Using two or more people, move dryer to desired installation

location.

2. Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe the interior of the

drum thoroughly with a damp cloth.

3. Take two of the cardboard corners from the carton and place

them on the floor in back of the dryer. Firmly grasp the body

of the dryer and gently Iay it on its back on the cardboard

corners.

4. With one of the legs in hand, check the ridges for a diamond

marking. That's how far the leg is supposed to go into the

hole.

5. Start to screw the leveling legs into the holes by hand. (Use a

small amount of liquid detergent to lubricate the screw

threads so it is easier to turn the legs.) Use a 1-inch wrench or

socket wrench to finish turning the legs until you reach the

diamond mark.

Now stand the dryer up.

6. Remove the service door of the meter case by lifting it up at

the back. Install the money-accepting

device. (Refer to

manufacturer's

instructions for proper installation.)

i!ii if! i i!i,: _ii_ ' iiiiii!! i iii_ ( iio i_i !i_ i _i_i

!i_ _i!_ cii:i _ii_ !:_

Remove red cap from gas pipe.

Connect gas supply to dryer. Use pipe-joint compound

resistant to the action of LR gas for gas connections. If

flexible metal tubing is used, be certain there are no kinks.

If necessary for service, open the toe panel. Use a putty knife

to press on the toe panel Iock located at the center top of the

toe panel. PulI downward on the toe panel to open. Toe panel

is hinged at the bottom.

Open the shutoff valve in the gas supply line.

Test all connections by brushing on an approved noncorrosive

leak-detection

solution. Bubbles will show a leak. Correct any

leak found.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured to

exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into final position. Do not crush or kink vent. Make

sure dryer is level.

3. Check to be sure there are no kinks in the flexible gas line.

With dryer in final position place leve! on top of the dryer, first

side to side; then front to back. If the dryer is not level, adjust

the legs of the dryer up or down until the dryer is level.

Electrica_ Shock Hazard

P_ug into a grounded

3 prong out_et,

Do not remove ground

prong,

Do not use an adapter.

Do not use an extension

cord,

Failure to follow these instructions

can result in death,

fire, or electrical

shock,

For dryers using coin slides, use the adapter kit supplied with

the dryer.

7. Replace the meter case service door. Put the coin vault with

lock and key in the meter case opening.

8. Remove cardboard or hardboard from under dryer.

Plug into a grounded 3 prong outlet.

Check dryer operation (some accumulated

time may be on

the timer due to factory testing).

Insert coins in slide and press slide in slowly. (Operating time

will accumulate per number of coins and type of timing cam

used.) Push START/RESTART button. Using a full heat cycle