FirePro ST522E Kullanıcı Kılavuzu - Sayfa 2

Duman Alarmı FirePro ST522E için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. FirePro ST522E 5 sayfaları.

Sayfayı Yazdır

respond to it to reduce the risk of damage, injury, or death

that may result from fire. If a household member is hard

of hearing, install special smoke alarm devices with lights

or vibrating devices to alert occupants.

7: Smoke alarm devices can only sound their alarms when

they detect smoke or detect combustion particles in the

air. They do not sense heat, flame, or gas. This smoke

alarm device is designed to give audible warning of a

developing fire. However, many fires are fast - burning,

explosive, or intentional, and others are caused by

carelessness or safety hazards. In this instance, smoke

may not make the smoke alarm sound QUICKLY

ENOUGH to ensure safe escape.

8: Smoke alarm devices have limitations. This smoke alarm

device is not foolproof and is not warranted to protect

lives or property from fire. Smoke alarm devices are not a

substitute for insurance. Homeowners and renters should

insure their lives and property. In addition, it is possible

for the smoke alarm device to fail at any time. For this

reason, you must test the smoke alarm device weekly and

replace unit every 10 years.

Do Not Install Smoke alarm devices in the

following places:

1: Near appliances or areas where normal combustion

regularly occurs (kitchens, near furnaces, hot water

heaters). Use a specialised smoke alarm device with

unwanted alarm control for these areas.

2: In areas with high humidity, like bathrooms or areas near

dishwashers or washing machines. Install at least 3m

away from these areas.

3: Near air returns or heating and cooling supply vents.

Install at least 1 metre away from these areas. The air

could blow smoke away from the detector, interrupting its

alarm.

4: In rooms where temperatures may fall below 5℃ or

rise above 45℃, or in humidity higher than 85%. These

conditions will reduce battery life or cause a fault alarm.

5: In extremely dusty, dirty, or insect-infested areas.

Particles interfere with smoke alarm device operation.

Operation:

Testing

Test the unit to ensure proper operation by pressing the test

button. This will sound the alarm if the electronic circuitry,

bracket is mounted, horn and battery are working. If no

alarm sounds, there is a defective battery or other failure,

you can refer to "Trouble shooting" section for solution.

DO NOT use an open flame to test your alarm, you could

damage the alarm or ignite combustible materials and start

a fire.

CAUTION: Due to the loudness (85 decibels) of the alarm,

always stand an arms-length away from the unit when

testing.

Test the alarm weekly to ensure proper operation. Erratic or

low sound coming from your alarm may indicate a defective

alarm, you can refer to "Trouble shooting" section for

solution.

NOTE: WEEKLY TESTING IS REQUIRED.

LED indicators

Red LED-Flashing once every 40 seconds: indicates that the

smoke alarm device is operating properly.

Red LED-Flashing: when the test button is pressed, or when

the smoke alarm device sense particles of combustion and

goes into alarm (constant pulsating sound), the red LED

will flash once per second. The flashing LED and pulsating

alarm will continue until the air is cleared or release test

button.

Red LED-Alarm silencer (Hush mode) indication: The red

LED will flash once every 8 seconds, indicating the smoke

alarm device is in the alarm silence (Hush) mode.

Low battery indication - An intermittent "chirp" with red

LED flashes once every 40 seconds: indicates that the

battery is low. You may press the test button to pause alarm

for 10 hours, but it will reset automatically after 10 hours.

Fault indication - The alarm chirp occurs every 40 seconds.

NOTE: When the units chirp once every 40 seconds,

you can press the test button temporarily for pausing this

warning tone for 10 hours, it can still normally detect smoke

during this period, it only removes nuisance warning tone.

You can refer to "Trouble shooting" for a solution, if there

are still failures, you MUST replace it with a new alarm

at once or contact you retailer during warranty.

Alarm silence (silence mode)

Whilst the unit is alarming, if you push the test button,

it will stop the unit alarming for approx 10 minutes. The

red LED will flash once every 8 seconds, it indicates the

smoke alarm device is running in silence mode. Smoke

alarm devices are designed to minimise nuisance alarms.

Combustion particles from cooking may set off the alarm

if the alarm is located close to the cooking area. Large

quantities of combustible particles are generated from spills

or when grilling/frying. Using the fan on a range hood

that vents to outside (non-recirculating type) will also help

remove these combustible particles from the kitchen. The

alarm silence (test button) is extremely useful in a kitchen

area or other areas prone to nuisance alarms. The silence

feature is to be used only when a known alarm condition,

such as smoke from cooking activates the alarm.

The smoke alarm device is desensitised by pushing the

- 2 -

Document NO.: FP522V-001 2020.02.18 Version: A