Whirlpool 24" (58 CM) Kurulum ve Kullanım Kılavuzu - Sayfa 4

Havalandırma Davlumbazı Whirlpool 24" (58 CM) için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Kılavuzu indirin. Whirlpool 24" (58 CM) 24 sayfaları. 24" (58 cm), 30" (76.2 cm), 36" (91.4 cm) range hood

Sayfayı Yazdır

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Drill

1 " (3 cm) drill bit

" (3 mm) drill bit for pilot holes

Pencil

Wire stripper or utility knife

Tape measure or ruler

Caulking gun and weatherproof caulking compound

Flat-blade screwdriver

Phillips screwdriver

For vented installations, you also need:

Saber or keyhole saw

Compass or 6 " (15.9 cm) circle template (if using a 3¼" x

10" (8.3 x 25.4 cm) rectangular vent to 6" (15.2 cm) round

vent transition)

Vent clamps

Metal snips

Parts supplied

Remove parts from package. Check that all parts are included.

4 - #10 x

" type A truss phil screws

Filter

3 " x 10" (8.3 x 25.4 cm) vent connector/damper

2 - #8B sheet metal screws

Parts needed

For direct wire installation

UL listed or CSA approved

75-watt max. incandescent light bulb

Power supply cable (if needed, for direct wire installation)

For power supply cord installation

UL Listed Power Supply Cord Connection Kit marked for

range hood use.

75-watt max. incandescent light bulb

For vented installations, you also need:

3 " x 10" (8.3 x 25.4 cm) or 6" (15.2 cm) round metal venting

3 " x 10" (8.3 x 25.4 cm) to 6" (15.2 cm) vent transition piece

if using 6" (15.2 cm) round venting.

For cabinets with recessed bottoms:

Two, 2" (5.1 cm) wide filler strips. Length and thickness

determined by recess dimensions.

Four flat head wood screws or machine screws with washers

and nuts (to attach filler strips).

INSTALLATION REQUIREMENTS

" (12.5 mm) strain relief

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located inside the range hood on

the rear wall.

Range hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance. Consult the

cooktop/range manufacturer installation instructions before

making any cutouts.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

All openings in ceiling and wall where range hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

1 "

(3.8 cm)

12"

(30.5 cm)

(22.9 cm)

(5.1 cm)

(15.2 cm)

(1.9 cm)

7 "

(19.1 cm)

23 " (60.6 cm) - 24" (61.0 cm) model

29 " (75.9 cm) - 30" (76.2 cm) model

35 " (91.1 cm) - 36" (91.4 cm) model

(2.5 cm)

1 "

(3.8 cm)

(9.5 mm)

17 "

(44.5 cm)