n
From inside the cabinet,
position
each
clamp
so that the hole in the clamp
aligns with the hole in the burner
box. Insert
a screw into the hole and secure cooktop
to countertop
by hand-tightening
each
screw.
To avoid damaging
cooktop surface,
do not overtighten
screws.
Note: If countertop
is unusually
thick, longer
mounting
screws can be used with the
clamps
to secure the cooktop
to the
countertop.
1
rear
of
cooktop
Ill e
pressure
regulator
.
gas-flow
arrow
polnttng
up
6
n
Install the pressure regulator
with the
arrow on the regulator
pointing
up toward
unit and in a position
where
you can reach
the access cap.
IMPORTANT: All connections
must be
wrench-tightened,
Do Not make
connections
to the gas regulator
too tight.
Making
the connection
too tight may
crack the regulator
and cause a gas leak.
Do Not allow the regulator
to turn on the
pipe when tightening
fittings.
l/2" nipple
flexible
connector
l/2" nipple
I
I
I
f=l-?T
'
l/2" adapters
'
I
manua/shutoff
valve
presslre
regulator
All connections
must be wrench-tightened.
7
n
Assemble
the flexible
connector
from the gas supply pipe to the pressure
regulator
in this order:
l/2" adapter,
flexible
connector,
l/2" adapter
and l/2" nipple.
8
n
Use pipe joint compound
resistant to
the action
of Natural
and L.Pgas to seal all
gas connections.
If flexible
connectors
are
used, be certain
connectors
are not kinked.
9
n
Open the shutoff valve in the gas
supply line. Wait a few minutes
for gas to
move through
the gas line.
10
w Use a brush and liauid
detergent
to test all gas conn&ctions
for
leaks. Bubbles around
connections
will
indicate
a leak. If a leak appears,
shut off
gas valve controls
and adjust connections.
Then check
connections
again.
NEVER TEST
FOR GAS LEAKS WITH A MATCH OR OTHER
FLAME.
Clean all detergent
solution
from
cooktop.
11
n
Plug the power supply cord into
the grounded
outlet.
burner cap
12
n
Place trim rings over each
burner. Find the two locc?ting tabs under the
burner cap and mount cap over the slots in
the burner base. Place burner grates over
burners and caps.
Electronic Ignition System -
initial lighting
Cooktop
burners use electronic
ignitors in
place
of standing
pilots. When the cooktop
control
knob turned
to the 'LITE" position,
the system creates
a spark to light the
burner. This sparking
continues
until the
control
knob is turned
to the desired
setting.
w Cl Teck the operation
of the
cooktop
burners. Put a 'pan of water on
each
burner. Push in and turn each
control
knob to 'LITE" position. The flame should
light within 4 seconds.
Do Not leave the
knob in the "LITE" position after burner
lights.
If burners do not light properly,
turn control
knobs to the 'OFF" position.
Check
that
power supply cord is plugged
in and that
circuit
breaker
or house fuse has not blown.
Check
that the shutoff valve is in the 'ON"
position.
Check
operation
again.
If a burner
does not light at this point, contact
your
Whirlpool
dealer
for assistance.
Note: A correctly
adjusted
sealed
gas
burner
may blow out when
a pan is not on
the burner.
14
n
After burner
lights,
turn control
knob to "HI"
position.
Check
each
cooktop
burner for proper
flame. The
small inner cone should have a
very distinct
blue flame
l/4" to
l/2" long, the outer cone is not
as distinct
as the inner cone.
15
n
Push in and turn each
control
knob to the "WARM" setting. The "WARM"
flame should be a minimum,
steady, blue
flame and should extend
to the other edge
of the burner cap. A stable flame should be
maintained
when the control
knob is
changed
from"HI"
to "WARM".
If flame
needs adjusting,
turn the control
knob to
the 'HI" position
for five minutes. Then turn
the control
knob back to the "WARM"
position
and remove
the control
knob. Use
a screwdriver
to turn the adjustment
screw
in the center
of the valve stem. Replace
the
control
knob. Check
the adjustment
by
turning
the control
knob from 'HI" to
"WARM" several times. There is no
adjustment
to the 'SIM" setting.
finished
installing
your new
Whirlpool
cooktop.
To get the
most efficient
use from your new
cooktop,
read your Whirlpool
Use &
Care Guide.
Keep Installation
1 Congratulations
1
to cooktop
for easy reference. The
instructions
will make reinstalling
Panel D
Sayfayı Yazdır