Whirlpool 761883306 Kurulum Talimatları Kılavuzu - Sayfa 3
Havalandırma Davlumbazı Whirlpool 761883306 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Whirlpool 761883306 7 sayfaları. 30/36" convertible range hood
Sayfayı Yazdır
Venting requirements
Horizontal Wall Venting
Now start...
With range hood in kitchen.
Slide cardboard
or hardboard
under range
before moving
range across floor to
prevent
damaging
floor covering.
Cover countertop,
cooktop
or set-in range
with a thick, protective
covering
to prevent
damaging
countertop.
3-l/&x
10"
throuah
the wall
f ' f
Aib
I
I cap
I
1 Put on safety glasses and gloves.
Fire Hazard
Venting
system must terminate
to the
outside.
Do Not vent exhaust
air into spaces
within
walls or ceilings
or into attics,
crawl spaces or garages.
Use metal duct only.
Do Not use four-inch
laundry-type
wall
caps.
Do Not use plastic ductwork.
Flexible
metal duct is Not recommended.
If it is used, calculate
each foot of flexible
metal duct as two feet of straight
duct.
Flexible
metal elbows
count twice as
much as standard
elbows.
Do Not use to exhaust
hazardous
or
explosive
materials
and vapors.
Failure to follow these instructions
could
result in a fire.
2
n
Disconnect
and move freestanding
range from cabinet
opening
to provide
easier access to upper cabinet
and rear
wall. Put a thick, protective
covering
over
cooktop,
set-in range or countertop
to
protect
from damage
or dirt
3
H Determine
which
venting
method
Figure 3
A
(roof or wall venting
or non-venting)
you
need to use. This range hood is shipped
for
non-vented
installation.
If non-venting
(recirculating)
installation
is
desired,
follow
instructions
on Panel D.
7" min. diameter
round ductwork
*I...
.
-.-m..---l
wall cap
elbow
: :'I-'
.:
I I*\
J
I I
3-1/4"x
10" to round
'.{ a. l t
l \
ductwork
transition
-:,,--'
:.--
Vented installation
vent baffle
Figure 4
Recommended
ductwork length
Use 3-l /4" x 10" or 7" ductwork
with a
m'aximum
length
of 26 feet for ductwork
system. For best performance,
use no more
Wan three 90" elbows. To calculate
the
length
of system you need, add the
equivalent
feet for each ductwork
piece
used in the system. See the following
examples.
Ductwork
needed
for insfallofion
is not
included.
Wall or roof caps used must have
backdrafl
damper.
Determine
which
outside
venting
method
needs to be used NOTE: If a non-vented
(recirculating)
installation
is desired,
follow
instructions
on Panel D.
The length
of the ductwork
and number
of
elbows should be kept to a minimum
to
provide
efficient
performance.
The size of
the ductwork
should be uniform.
Do Not
install two elbows together.
Use duct tape
to seal all joints in the ductwork
system.
Ductwork
can terminate
either through
the
roof or wall. Use caulking
to seal exterior
wall or roof opening
around
exhaust
hood.
For the most efficient
and quiet operation,
it
is recommended
that the range be vented
vertically
through
the roof through
7" round
ductwork.
Figures l-4 show common
venting
methods
and what types of materials
are needed.
Vertical Roof Venting
roof cap
.'Q:,
4
F
W Remove
screws from vent baffle on
top of range hood. Remove
vent baffle.
3- l/4" x 10" ductwork system
3 - 114" x 10"
H-
6 ft.
elbow
wall cap
0
3
-7
* ft' Maximum
1 - 90" elbow IenLth
= = 26 5ft feet
8 feet straight
= 8ft.
u
1 - wall cap
= Oft.
Length of
3- l/4" x 10" system
= 13 ft.
in
top of range hood so that the word
"Vented"
is facing
up. Fasten vent baffle
with screws.
Recommended
standard fittings
7" round
through
t
roof
damper
locatec?-
as far from hood
as possible
3-114" x 10" 90"
3-114" x 10" flat
3-l/4"
x 10" wail
elbow = 5 ft.
elbow = 12 ft.
cap=oft.
7" ductwork system
knockouts
6
n
Remove
knockout
from the wiring
opening
(top or rear) to be used.
For rectangular
venting,
remove
only the
3-l/4"
x 10" rectangular
opening
knockout.
For round ductwork
venting
through
roof,
remove
both opening
knockouts.
Figure 1
Vertical Roof Venting
ro/f cap
/
3-1/4"x
10"
Maximum
length
= 26 feel
to 7"
transition
1 - transition
= 4,5 ft
2 - 90" elbows
=lO
ft.
8 feet straight
= 8
ft.
1 - wall cap
= 0
ft.
Length of 7" system
= 22.5 ft
3-114" x 10"
through
the roof
Recommended
standard fittings
terminal
box
3-114" x 10"
damper
3-114" x IO" to
3-114" x 10" to 7"
7" to 3-114" x 10"
7" = 4.5 ft.
90" elbow = 5 ft.
90" elbow = 9 ft.
from
n
Remove
terminal
box cover
Figure 2
range hood
90" elbow =
7" to 3-114"
5 ft.
xlO"=lft.
;",";lbow
=
I';wtizll
cap
.
.
Panel B