Whirlpool 99044504A Kurulum Talimatları ve Kullanım & Bakım Kılavuzu - Sayfa 3

Havalandırma Davlumbazı Whirlpool 99044504A için çevrimiçi göz atın veya pdf Kurulum Talimatları ve Kullanım & Bakım Kılavuzu indirin. Whirlpool 99044504A 24 sayfaları. 30" (76.2 cm) and 36" (91.4 cm) range hood

Sayfayı Yazdır

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

Ducted fans must always be vented outdoors.

CAUTION:

For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION:

To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING:

TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Drill

1 " (3.0 cm) drill bit

" (3.0 mm) drill bit for pilot holes

Pencil

Wire stripper or utility knife

Tape measure or ruler

Caulking gun and weatherproof caulking compound

Flat-blade screwdriver

Phillips screwdriver

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

WARNING:

TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING:

TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:

SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

NEVER PICK UP A FLAMING PAN - you may be burned.

DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

WARNING:

To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

For vented installations, you also need:

Saber or keyhole saw

Vent clamps

Metal snips

Compass or 8" (20.3 cm) circle template

Parts supplied

Remove parts from package. Check that all parts are included.

Filter

4 - #10 x

" mounting screws

7" (17.8 cm) round transition plate

7" (17.8 cm) damper/vent connector

3 " x 10" (8.3 x 25.4 cm) damper/vent connector