Whirlpool GZ5730XR Series Kurulum Talimatları ve Kullanım & Bakım Kılavuzu - Sayfa 6

Havalandırma Davlumbazı Whirlpool GZ5730XR Series için çevrimiçi göz atın veya pdf Kurulum Talimatları ve Kullanım & Bakım Kılavuzu indirin. Whirlpool GZ5730XR Series 24 sayfaları. 30" (76.2 cm) and 36" (91.4 cm) convertible range hood
Ayrıca Whirlpool GZ5730XR Series için: Boyutlar (1 sayfalar), Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu (24 sayfalar), Kurulum Talimatları ve Kullanım & Bakım Kılavuzu (24 sayfalar), Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu (24 sayfalar)

Sayfayı Yazdır
Whirlpool GZ5730XR Series Kurulum Talimatları ve Kullanım & Bakım Kılavuzu
iNSTALLATiON iNSTRUCTiONS
1. If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to upper
cabinet or rear wall. Slide cardboard or hardboard under
range before moving range across floor to prevent damaging
floor covering. Otherwise put a thick, protective covering over
countertop, cooktop or range to protect from damage
or dirt.
2. Determine which venting method (roof or wall venting or
non-venting) you need to use. This range hood is shipped for
non-vented installation.
7" {17,8 cm) round
vertica_
vent
system
wall
5"
1 V4"(3.2 cm)
2"
(122 cm)
dia. hole
(5_1 cm)
wall
W' (3.0 ram)
1 F,"
pilot holes
(3.8 cm)
Hood size
A
30" (76,2 cm)
13_% '' (35,4 cm)
36" (91,4 cm)
16_5A6 '' (43,0 cm)
wood shim strips
(recessedcabinet
bottoms only)
3V4" x 10" {8,3 x 25,4 cm} horizonta_
vent
system
centerline
"",,q
1¼" (3,2 cm)
3¾"
(9_8 cm) (3.2ram) 511/_,,__7,/,,
' (19(19c2)m)
(13.3 cm)
3,
4,
Drill four W' (3.0 mm) pilot holes for hood mounting screws. If
cabinet has recessed bottom, add wood shim strips on each
side.
From the following diagrams, select the diagram for your
installation.
Vented installations: Cut the vent system and electricN wiring
access holes as required.
Non-vented installations: Drill only the 1_/_"(3.2 cm) dia. wiring
access hole required.
[]
If wiring through the top, use location shown in vertical
vent systems.
[]
If wiring through the back, use location shown in
3%" x t0"
{8,3 x 25,4 era) rectangular
vertica_
vent
system
5w'
horizontal vent system.
Set the hood on a protective covering such as cardboard or a
large towel. Remove the 7" (17.8 cm) round vent plate from
5"
1W'
wall
1V4"(3.2 cm)
2"
(12.7cm)
(3,2 cm)
dia, hole
(5,1 cm)
A. 7" (17.8 cm) round vent plate